What Size Trailer Tongue Will Fit Fulton Fold-Away Coupler Hinge Kit FHDPW230300

Question

Question:

The major many gigs is 2 X 3 inches is that one side two inches one side 3 inches or is that 2 inch box 3 inches high? Thanks

asked by: Brandon

1

Helpful Expert Reply:

The 2 x 3 inch measurement means 2 inches wide by 3 inches tall. That is the dimension of the trailer tongue that is compatible with Fulton hinge kit # FHDPW230300. The openings on the hinge are slightly larger to fit over a 2 inch wide and 3 inch tall tongue.

expert reply by: Michael H

1

Answer 1

The reason the wall thickness is listed for the Fulton Fold-Away Coupler Hinge Kit, part #FHDPB230101, is because the Torx bolts included in the kit are a certain length and the nuts may not catch the threads when installing the hitch due to the 1/4…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…

view full answer...

Answer 11

I attached a picture to this page that has a wiring diagram for the Furrion Indoor Enclosed Amplified Subwoofer #FSW8P12CF that you referenced. I attached a review video for this for you to check out as well.

view full answer...

Answer 12

The interior lights of your trailer would be powered by the 12 volt accessory circuit on the 7-way of your 2010 GMC Sierra. You will want to check the 1:00 position of the 7-way on your truck with a circuit tester like part #PTW2993 to verify if…

view full answer...