Voyager Brake Controller Red Light Not Coming On with Brakes Applied on a 2004 Chevy Silverado
Question:
We have a 2004 Chevy Silverado with the Voyager brake controller. We have used it for about 5 years now. Just yesterday, when hauling our fifth wheel, the green light was on, but when pressure was applied to the brakes, the red light did not come on and we are not sure if the brakes on the trailer are kicking in! The maunal bar was adjusted also. Please help with any suggestions!
asked by: Wendy S
Expert Reply:
There are several possible causes that would lead the red light not to come on when applying the brakes or manual override on the Tekonsha Voyager Brake Controller, # 39510. First, if truck is not moving, the brakes will not activate. You will also want to check to make sure the power setting is not too low.
There may be no signal from the brake light switch. You will need to test the red wire from the back of the brake controller using a circuit tester like # PTW2993. If there is no voltage, it could be a loose or broken connection. You can also check the blue wire. with no brakes applied, test for voltage. If it shows voltage with no brakes applied, there is a short to the blue wire. Make sure the ground is also properly connected.
You may need to level the sensor. First connect the trailer to the truck. Set the power knob to maximum. Step on brakes and hold them there. While holding the brakes, rotate the power knob back until the light changes from green to red. Then rotate it back the other way slowly until the light appears orange. Dim orange is a normal setting. Bright orange is an aggressive setting. Dim red is the most aggressive setting.
There could also be a blown stop light fuse. Check the under-hood fuse box for the fuse. There should be a legend on the fuse box lid that shows where the fuse is located. You will also want to double check that all the under-hood connections for the brake controller/tow package on your 2004 Chevy Silverado are made and that the fuses are in place and not blown. I have included a link to an FAQ article that explains these connections and link to the brake controller instructions below.
Products Referenced in This Question
Product Page this Question was Asked From
Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Manual Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- Indicator Lights
- Up to 90 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Trailer Brake Controller Wire Testing
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: tekonsha
- Q&A: Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors
- Q&A: Testing for Proper Voltage on the Brake Output Circuit
- Q&A: Charging a Trailer Breakaway System Battery Using the 12 Volt Circuit on a 7-Way Connector
- Search Results: voyager
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Brake Controller Installation: Starting from Scratch
- Video: Odor1 Refresh Premium Odor Eliminator Kit Review
- Article: Trailer Wiring Diagrams
- Shop: Replacement Mounting Bracket Kit for Tekonsha Prodigy P3 Trailer Brake Controller
- Shop: Spidy Gear Bed Webb Stretchable Cargo Net for Full-Size Truck Beds - 84" x 60" - Black
- Shop: Odor1 Arex 4000 Aerator Odor Eliminator System - 1 Tablet
- Shop: Rightline Gear Truck Bed Cargo Net w/ Integrated Tarp - Weatherproof - 121-1/2" x 106-1/2"
- Shop: Odor1 Refresh Premium Odor Eliminator Kit for Cars, Trucks, and Vans - Qty 1
- Shop: Replacement Switch for Curt Soft Trac I and II Trailer Breakaway Kits
- Video: Curt Trailer Breakaway Kit C52010 Review
- Video: Curt Trailer Breakaway Kit Switch Review
- Q&A: Voltage at Brake Magnets is 8 Volts with Brake Controller Set to Maximum
- Q&A: When do You Need a Breakaway Battery Charger and How Does it Function
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: Will a Dead Battery on a Breakaway Kit Cause the Vehicle to Not Be Able to Operate Trailer Brakes
- Article: Testing Brake Controls
- Article: Testing Breakaway Systems
- Search Results: trailer brake controller
- Video: Choosing the Right Brake Controller
- Shop: Trailer Wiring
Glen M.
5/29/2020
Red light stays on always. When you slide the slider light turns green. Tried it on 2 different trucks same issue. Camper brakes work fine on 2 other vechiles. Any ideas. Thx