Replacement Drop Leg Recommendation for Ram Model 2500 Series Drop Leg

Question

Question:

Hey yall, My boat trailer leg has rusted from salt water. It says, Ram Model 2500 Series Drop Leg. I want to make sure I order the correct replacement with pad. Can you provide a model number? Thanks!

asked by: Joe

0

Expert Reply:

For your RAM Model 2500 series drop leg jack the correct drop leg replacement you would need is the part # TJD-5000-FT that you referenced.

expert reply by: Jameson C

0

Answer 1

The Replacement Drop Leg #TJD-5000-FT is designed to be used with Ram TJD-5000 Series jacks so if that's what you have it will work for you. You can also compare the dimensions of this leg with your current one to see if they are equal.…

view full answer...

Answer 2

If you are talking about the drop leg #TJD-7000-FT then it could fit your 8000 series jack as long as all the measurements match up. This jack is 2 inches square and the distance from the center of one adjustment hole to the center of the next is…

view full answer...

Answer 3

I attached a chart that has the automotive cross reference for the Kodiak disc brake pads part #K2250CP that you referenced under the yellow heading. Probably the easiest to look up would be 1982 to 1992 Chevy Cavalier.

view full answer...

Answer 4

I went out to the warehouse and found that from the center of the bottom adjustment hole of the Replacement Drop Leg #TJD-5000-FT to the bottom of the footplate measured about 1-1/2" as you can see in the attached photo.

view full answer...

Answer 5

I do have a part number for you, "DF35000324" but the replacement drop leg for the Bulldog Square Jack with Footplate part #BD195354 is no longer available. Therefore, we could only offer you is a new jack, the Bulldog Square Jack…

view full answer...

Answer 6

I do have a possible option for you but the Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks - 3K #TJD-5000-FT only has a capacity of 3,000 lbs so that wouldn't be enough for your dump trailer. The possible option I have is the…

view full answer...

Answer 7

Yes, drop leg #TJD-5000-FT will fit trailer jack #MJSQ-2500B. The drop leg that comes with this jack is 1-3/4 inches square which is the same as #TJD-5000-FT. And it has the same hole spacing.

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Drop Leg Recommendation for Ram Model 2500 Series Drop Leg

Product Page this Question was Asked From

Continue Researching