Cross Reference Chart for Kodiak Trailer Disk Brake Pads to Automotive Applications

Question

Question:

i have a trailer broke down on highway and need brake pads asap, could i get these pads at a local parts store and what application could i look up to find them?

asked by: Donald

0

Expert Reply:

I attached a chart that has the automotive cross reference for the Kodiak disc brake pads part # K2250CP that you referenced under the yellow heading. Probably the easiest to look up would be 1982 to 1992 Chevy Cavalier.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Since your old V-bar light only uses a single wire it grounds the light through the mounting hardware. You will simply need to add a Ring Terminal #DW05736-1 to the ground wire on the V-Shaped Identification Light Bar #TN23MR. Then you will be able…

view full answer...

Answer 2

Hey Travis, While we haven't tested DeeMax's compatibility to TDE we have been receiving reviews from people that have tried and found them to be a fit. One review states that they successfully replaced their TDE 46304 calipers with…

view full answer...

Answer 3

Lights like the LED Clearance or Side Marker Trailer Light w/ Reflector #MCL0032RBB are more or less universal so as long as the light you're wanting to replace on your 2019 Heartland Landmark Newport 5th Wheel measures 2" x…

view full answer...

Answer 4

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do…

view full answer...

Answer 5

The Kodiak Ceramic Brake Pads #K2250CP are not shown on the cross reference chart you mentioned, but if you have the DBC-2250 calipers, these brake pads will work as a replacement. Check out the video linked below for more details on this product.…

view full answer...

Answer 6

From what we have found in the past, the TDE 46304 calipers are for 9.6", 10" or 12" rotors. Assuming you have the 10" or 12" rotors you can use the Kodiak Disc Brake Caliper #KDBC225DAC as a replacement.…

view full answer...

Answer 7

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 referenced in your question do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life…

view full answer...

Answer 8

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life so there is typically no…

view full answer...

Answer 9

The Tie Down Engineering (TDE) Brake Actuator 48980 also known as the 80LP/85LP is a 8,000 lb or 8,500 lb disc brake actuator with 2" coupler. In order to replace this, the best option we have is the Demco Hydraulic Brake Actuator part…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The spindles you have on your trailer are the same dimensionally as the standard 84 spindle so we have disc brake kits that will fit the spindles/axles. I confirmed this by checking with Tie Down. The Kodiak disc brake kit part #K2HR35DS that you…

view full answer...

Answer 12

I do have an option for you but we don't offer any replacement brake pads for the Tie Down Engineering (TDE) 46304 Caliper as the company is no longer in business. Therefore, our only option to you would be a full replacement for which I…

view full answer...

Cross Reference Chart for Kodiak Trailer Disk Brake Pads to Automotive Applications

Product Page this Question was Asked From

Continue Researching