Will Draw Tite Front Hitch 65022 Fit a 2006 Ford F-350 with Diesel Engine

Question

Question:

I have a 2006 f350 crew cab super duty with the 6.0 liter diesel. Will this fit with the diesel engine? Thanks

asked by: Ed H

0

Expert Reply:

Yes, the Draw Tite Front Hitch part # 65022 that you referenced has been confirmed as a fit for your 2006 Ford F-350 with a diesel engine. If you check out the install video I attached you can see it being installed on a diesel truck similar to yours.

expert reply by: Jameson C

0

Answer 1

The Curt Front Mount Trailer Hitch Receiver part #31114 which is a fit for a 2007 Ford F-250 Super Duty installs behind the bumper beam to the end of the frame on both the driver and passenger side. I have attached a photo below which shows this.…

view full answer...

Answer 2

The Draw-Tite 2-Inch Front-Mount Hitch, part #65022, will fit the Ford Super-Duty pickups for model years 1999 through 2007. It is compatible with pickups that are equipped with tow hooks (but these will need to be removed temporarily and…

view full answer...

Answer 3

For your 2005 Ford F-250 XLT Super Duty, I recommend the Draw-Tite Front Hitch, #65022, which is designed to be mounted in the front of your vehicle. If you have the optional OEM fog lights on your truck, you must remove or relocate them for receiver…

view full answer...

Answer 4

I attached a picture that shows the Draw Tite front hitch part #65022 installed on a 2000 Ford Super Duty just like yours and you can see the transmission cooler in the picture as well which means the two will easily fit together!

view full answer...

Answer 5

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 6

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 9

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 12

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Will Draw Tite Front Hitch 65022 Fit a 2006 Ford F-350 with Diesel Engine

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching