Why Does Curt Require Stabilizing Strap While Hidden Hitch and Draw-Tite Do Not

Question

Question:

Why do the curt hitch mounts require extra straps for bike carries and the DrawTight and others do not?

asked by: Justin D

0

Expert Reply:

Curt requires the strap to provide extra support for when the vehicle goes over rough pavement or experiences a sudden shock like hitting a pothole. Draw-Tite and Hidden Hitch feel that this isn't necessary with their hitches.

Because the strap is an extra expense, and because some vehicles just aren't well suited to using the strap, I'll usually recommend going with the Draw-Tite or Hidden Hitch models.

expert reply by: Mike L

0

Answer 1

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 2

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 7

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 8

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

There is a Titan hitch extender that should work for you, but would require a Titan hitch be installed on your truck to handle a tongue weight loaded that far from the hitch. It is Reese part #RP45292. You can use it as a 34 inch extension or cut it…

view full answer...

Answer 11

The Reese Titan Extension/Reducer you referenced, part #RP45292 would work great with the 2-1/2 inch Class V hitch on your Ram. As you mentioned, the extension has a 8K capacity when cut down to the 24 inch length, that will provide a 2 inch receiver…

view full answer...

Answer 12

You can use a 7-Way and 4-Way connector at the same time just as long as you are not overloading the light circuits. If your camper has a lot of outside lights like running lights, and brake/stop/turn lights then the lights that perform the same…

view full answer...