How to Pick Out JTs Strong Arm Jack Stabilizers for a Trailer

Question

Question:

I have a 2015 open range roamer 288flr and would like to put on JT strong arms on it. And would like to know model I need. It has power jacks on it

asked by: Randy

0

Expert Reply:

You will need to measure the distance between the landing gear feat. If the measurement is right at 58 inches or over you would want the Lippert Components JT's Strong Arm Jack Stabilizer Kit # LC191023 which is listed as a fit for 58 inches and over measurements.

If the distance is less than 58 inches you would need the kit part # LC191024 instead.

expert reply by: Jameson C

0

Answer 1

I can absolutely confirm the correct lift kit for your trailer. Based on your photos, you do in fact have a #10 Torflex axle, and they are compatible with the lift kits because you do not have 3" high-profile brackets (which just means the…

view full answer...

Answer 2

Thank you for the photo of the axle sticker; that's always helpful in helping us identify what you've got. That serial number is for a Torflex #10 axle, so the correct lift kit is the #K71-707-01 for a single axle or the #K71-707-02 if…

view full answer...

Answer 3

Is your axle a straight axle? Can you get me the diameter of it?

view full answer...

Answer 4

We can help you determine the correct JT's Strong Arm Jack Stabilizer Kit for your Keystone Cougar 5th wheel trailer, though the kits aren't designed to fit any certain model, and we don't have a way of knowing the distance between your…

view full answer...

Answer 5

It all depends on where you place the rear jacks for Lippert Ground Control 3.0 system #LC358590. I do not believe that the main landing gear legs would be a problem since they will be right at the front under the overhang. Most likely you will not…

view full answer...

Answer 6

That really depends on the clearance you have under the trailer where the spare resides. It's possible you'd have enough clearance but it really depends on where exactly it mounts. If the spare attaches to the cross-member on the front of the…

view full answer...

Answer 7

The Replacement Ball Assembly #UF19-001057 that you referenced can be used with an Andersen Ultimate fifth wheel adapter but it has to be used with an Ultra Fab stabilizer like the #UF19-950500 since we can't guarantee it would work on an EAZ…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...