Where Does Curt T-Connector Vehicle Wiring Harness Install on a 1999 Ford Super Duty

Question

Question:

How does this T? There is only one connector on either end.

asked by: Sam

0

Expert Reply:

T-Connector is a generic term that is applied to any trailer wiring harness that is plug and play. Models of the 1999 Ford Super Duty that came with a factory 4-Way would use the connector # C55243 to just plug in where the 4-Way plugs in.

expert reply by: Michael H

0

Answer 1

Yes, there are relays and fuses that will need to be installed on a 2000 Ford F-250 if not already present in order to activate the circuits for the brake controller and 7-way trailer connector. In order to check this you simply need take a look at…

view full answer...

Answer 2

Hopkins Plug-In Simple Wiring Harness #HM40155 has a 4-pole flat trailer connector and is intended as a replacement for a factory 4-pole on your 1999 Ford F-250. We do have other wiring kits for your truck depending on how it was equipped from the…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Where Does Curt T-Connector Vehicle Wiring Harness Install on a 1999 Ford Super Duty

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching