Recommendation for Towing a Waverunner with a 2014 Nissan Altima

Question

Question:

How about towing a waverunner? Can you Towing Altima

asked by: George

0

Expert Reply:

Sounds like you are wanting to tow a waverunner with your 2014 Nissan Altima, it would greatly depend on what the weight of the trailer ends up being and any limitations of your vehicle. I recommend consulting your owner's manual or Nissan about any limitations your vehicle may have.

If you have the towing capacity, then we have all the parts you will need right here. I recommend the Curt Class I hitch # C11352, because it has a towing weight of 2,000lbs and 200lbs of tongue weight. To complete your towing setup you will need wiring # 118470, a ball mount like # C45521, a pin and clip # F-4, and a ball. The ball you choose will depend on the size of the coupler on the trailer, some common sizes are the 2 inch ball # A-82 or the 1-7/8 inch ball # A-80.

I have also linked you to a Help Article about how to find tongue weight for your convenience.

expert reply by: Jackie C

0

Answer 1

The trailer hitch I recommend for your 2015 Altima is the Draw-Tite Sportframe Trailer Hitch Receiver, part #24796. I recommend this hitch because the Curt Trailer Hitch, part #C11352 requires the use of a safety strap like part #18050 when it is…

view full answer...

Answer 2

Yes, I can! To add a hitch to your 2024 Nissan Altima, I recommend the Draw-Tite item #24796. This hitch is custom fit and bolts to your Nissan with included hardware. It is a class I hitch with a 1-1/4" receiver. It has a 2,000 lbs towing…

view full answer...

Answer 3

There is a bulkhead underneath the 2015 Nissan Altima that will serve as a guide to line the hitch, #24796, up properly. Once the hitch is in place you will use it as a template to drill the holes needed for installation. I have included a link to…

view full answer...

Answer 4

The hitches like the part #24796 that would fit a 2014 Nissan Altima fit 2007-2015 Altima models so it would be safe to say that a hitch from a 2014 would fit a 2015. I attached an install video for you to check out as well.

view full answer...

Answer 5

I would be happy to help you! The best hitch for your 2017 Subaru Legacy is going to be the Draw-Tite Max-Frame Trailer Hitch Receiver item #75673. This hitch is custom fit and bolts directly to your Legacy with included hardware. This hitch has the…

view full answer...

Answer 6

We have a 3-3/4 inch rise that works great with your trailer, item #C45023 . It's the Curt Class I Drawbar - 3-3/4" Rise - 11-1/2" Long - 2,000 lbs drawbar. It is slightly taller than your desired rise. But once the trailer is hooked…

view full answer...

Answer 7

The recommended 2 inch Euro style ball mount for Curt trailer hitch #C11352 on a 2015 Nissan Altima is #C45572. I went out to the warehouse and pulled one to take some measurements. From the center of the pin hole to the part of the shank where it…

view full answer...

Answer 8

When we installed the Draw-Tite #24796 on a 2009 Nissan Maxima, we found that the hitch height and the setback was the exact same as the Curt #C11352 you referenced. This being said, the Euro-style ball mount won't work with the Draw-Tite hitch.…

view full answer...

Answer 9

The only hitch we offer for your 2007 Altima is a Class I hitch, which has a 2000 lb towing/ 200 lb tongue weight (the maximum amount of weight that can be suspended from the hitch) capacity. Using an adapter would lower the tongue weight capacity by…

view full answer...

Answer 10

For your 2006 Nissan Altima we have trailer hitches available that will allow you to tow a small trailer. The Curt Class 1 Hitch #C11264 will be a great option that is confirmed as a fit. Since this is a Class I hitch you have to use the recommended…

view full answer...

Answer 11

The light-duty Class I hitches made for your 2017 Nissan Altima, Draw-Tite #24796 and Curt #C11352, both shown on the linked page, have a tongue weight (TW, downward force) rating of 200-lbs. This is true for all Class I hitches for all vehicles.…

view full answer...

Answer 12

Of the hitches available for your 2009 Altima Sedan, the Curt #C11352 would be recessed under the vehicle by less than the Draw-Tite model. When installed, the Curt #C11352 hitch pin hole would be recessed 5 inches under the vehicle (distance from…

view full answer...

Recommendation for Towing a Waverunner with a 2014 Nissan Altima

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching