Replacement Velcro Recommendation for a Truxedo Lo Pro QT Tonneau Cover

Question

Question:

Looking for replacement Velcro strips for our 2011 Chevy Silverado. The cover is a Truxedo Lo Pro. Box size is 5 1/2. The 1 1/2 inch strip will be too big. Can you assist in helping us find the current product? Thanks,

asked by: Bridget

0

Expert Reply:

The correct replacement Velcro for a Truxedo Lo Pro QT tonneau is the part # TX1115174. This strip is 1-5/16 inches wide and could be trimmed to length to fit your truck.

expert reply by: Jameson C

0

Answer 1

I contacted TruXedo with the number on your cover to verify that you have the Lo Pro QT, part #TX581101, on your 2006 Chvevrolet Silverado. The replacement cover you need is part #TX1117651.

view full answer...

Answer 2

If the TruXedo tonneau cover you have on your 2003 Chevrolet 2500HD is the Lo Pro QT then yours is part #TX581101. In which case the replacement tarp you need is part #TX1117651. If you have a different TruXedo let me know which it is and…

view full answer...

Answer 3

I do have a tonneau cover that fits your 2003 Sierra 2500 6-1/2 ft bed but the TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX548101 fits Dodge trucks. The TruXedo Lo Pro Soft Roll-up tonneau Cover that you need for the GMC Sierra is #TX581101. If…

view full answer...

Answer 4

We have replacement tonneau cover Velcro that is exactly 1-5/16 inches wide with the Truxedo part #TX1115174 which would fit your rails. It can be cut down shorter too as it is 80 inches long.

view full answer...

Answer 5

The Replacement TruXedo Shur-Bond Velcro Brand Fastener for 6-1/2' Beds -1-5/16" Wide #TX1115174 is designed to fit TruXedo Lo Pro or Original Edge tonneau covers. While I can't say for sure whether or not these will fit a…

view full answer...

Answer 6

The TruXedo Shur-Bond Replacement Velcro #TX1115174 does fit the Lo Pro QT tonneau covers but measures more than 1-inch wide; it is 1-5/16-inches in width and 80-inches long. This slides into the cover's rail. We also have a screw-on Velcro strip…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

To add a in-bed 7-way to your 2024 Chevy Silverado 2500 to make towing with a 5th wheel easier, I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long item #C58FV. This harness puts a 4-way and 7-way…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Velcro Recommendation for a Truxedo Lo Pro QT Tonneau Cover

Product Page this Question was Asked From

Continue Researching