Is Bumper Trimming Required to Install a Trailer Hitch on a 2016 Chrysler Town and Country
Question:
I was wondering if this hitch can be installed on the 2016 Town and Country without any trimming as mine is a lease!. And, if so, what the clearance from the hitch opening to the ground is?
asked by: Molly
Expert Reply:
Based on an installation we did of Curt hitch # 13364 on a 2016 Chrysler Town and Country you will not have to trim the rear fascia to install the hitch. However, it may press up some on the bottom of the fascia directly above the receiver. I have included a link to a video showing installation on a 2016 model for you.
When installed the hitch measures approximately 13-1/4 inches for the ground to the top of the receiver opening. If measuring to the bottom of the receiver it would be approximately 11 inches.
If you plan on doing some towing I recommend etrailer ball mount kit # EBMK4EL. It comes with a ball mount with a 2-3/4 inch rise or 4 inch drop, interchangeable ball set, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
And to add a 4-Way trailer connector to the rear of the vehicle I recommend # C56331. I have included a link to a video showing how the wiring installs as well.
Products Referenced in This Question
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
etrailer Ball Mount Kit - Extra-Long - 2-3/4" Rise or 4" Drop - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: No-Drill Mount for Electrical Mounting Bracket - Short
- Shop: Mounting Bracket 4-Pole Flat
- Shop: Curt LED 4-Way Flat Connector (Vehicle End) Tester
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Search Results: wire wrap
- Video: Curt Wiring Harness Installation - 2019 Dodge Grand Caravan
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Wire Loom, 3/8" Diameter, 10' Long
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer hitch
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer hitch wiring
- Shop: Brake Controller
- Video: Curt 4-Pole Flat Trailer Connector Mounting Bracket Review
- Article: Trailer Wiring Diagrams
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Shop: Suspension Enhancement
- Q&A: Recommended Hitch for a 2024 Toyota Grand Highlander
- Video: Choosing the Right Brake Controller
- Search Results: brake controller
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Measure for Trailer Hitch Drop