Dimensions of the Brophy # BP06 Backing Plate

Question

Question:

What are the dimensions and material thickness of the BP06 Backing Plate for the RR06 Swivel D-Ring?

asked by: Jim D

0

Expert Reply:

I went out into our warehouse and measured the Backing Plate # BP06 and found that the outside dimensions are 6-7/16 inches by 6-1/2 inches. The circle in the middle has a 4-5/8 inch diameter and the overall thickness of the metal plate is .11 inches

The bolt holes have a distance of 3.80 inches apart with a diagonal measurement of 5.40 inches.

See picture.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I pulled the Brophy Trailer D-Ring Tie Down, #RR06, from my warehouse to measure and verified that the diameter of the flange is in fact 6-5/16 inches. I also verified that all other measurements on the product page are correct. I have attached the…

view full answer...

Answer 2

Thank you for the photo! The Replacement Shark Fin Camera Mounting Bracket #FRCBRKT-BL that you referenced is just the bracket so to utilize the Furrion Vision S camera system you will need the whole camera kit. I recommend going with the Furrion…

view full answer...

Answer 3

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Dimensions of the Brophy # BP06 Backing Plate

Product Page this Question was Asked From

Continue Researching