Recommended Replacement Cradle And Strap For Older Version Thule Hitching Post 4-Bike Rack

Question

Question:

I have a THULE 91944 Hitching Post Four Bike Rack. I need a strap that would work with the Cradle 753-2757. Do you have a recommended strap to replace.

asked by: Jeff O

0

Expert Reply:

The cradles and straps are no longer being made for the 944 bike carrier you have but I do have good news.

You can simply replace the cradle and strap with part # 853-5829 and part # 753-3535. The will work with your bike rack and are confirmed as a fit by my contact at Thule. They will have a different appearance, so you may wish to replace all of the cradles and straps at one time.

expert reply by: Jeffrey L

0

Answer 1

My solution for this is to approach it from another angle and REDUCE your hitch size, since the sleeve adapters that increase the hitch of this specific model, the Thule Hitching Post 945, are no longer widely available. I recommend the Hitch Reducer…

view full answer...

Answer 2

It looks like you purchased the Thule T3 Cradle, #853-5829, and the T3 Strap, #753-3535. These two items should work well together so I made a short demonstration video for you. If you think you may have received a different strap or are missing a…

view full answer...

Answer 3

The Replacement T3 Cradle Body #853-5829 that you referenced is designed to fit 1 inch diameter rack arms. If you measure the diameter of your rack arms and they are 1 inch in diameter the #853-5829 could work. Without knowing what rack you have it…

view full answer...

Answer 4

The Replacement T3 Cradle Body for Thule Bike Carriers #853-5829 is 2-1/4 inches wide at the base but will support a frame over 2 inches without issue. The Replacement Rubber Strap for Thule T3 Bike Carrier Cradles #753-3535 are 10-1/2 inches long so…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...