What is the Ball Weight Capacity of the Tow Ready Pintle Combo C48200

Question

Question:

What is the Gross Weight on the Ball from the Curt Ball Mounts - C48200 Ball Pintle Hook Combo with 2-5/16 Ball

asked by: Howard

0

Expert Reply:

The ball weight carrying capacity of the Tow Ready Pintle Combo # C48200 is 16,000 pounds when used as a ball mount as long as you keep the 2-5/16 ball. If you would purchase a 2" ball to use with th # C48200 this capacity drops to 10,000 pounds.

When used as a pintle with a lunette ring, the capacity is 16,000 pounds.

expert reply by: Patrick B

0

Answer 1

Buyers Products 2" Pintle Hook Mount #337PM90 does not come with hardware to mount a pintle hook to it. Some of the pintle hooks come with hardware, such as Curt model #C48210. Or if you just need hardware you can use #C48330.

view full answer...

Answer 2

I did some checking and basically the cutout bumper is the regular factory bumper. The Curt hitch, #C15312, will fit up tighter and a little more recessed, apparently the same way the factory hitch does if it were installed. Some people like the…

view full answer...

Answer 3

If your 2002 Chevy Silverado 3500 features the standard factory rear bumper (and not a 10 inch deep drop bumper) then the correct Curt hitch is the Class V #C15312 that you referenced. I have attached an image that shows the difference between a…

view full answer...

Answer 4

The best option I have for an adjustable pintle hook that slides into a 2" hitch is the Curt Pintle Hook Mounting Plate part #C48341 with the Curt Pintle Hook part #C48210. I am not aware of any way to use a swivel type pintle hook with a…

view full answer...

Answer 5

The Curt Pintle Hook with 2-5/16 Inch Hitch Ball #C48200 features mounting hole dimensions that are 1-3/4 inches apart (on center) vertically, and 3-1/2 inches apart (on center) horizontally. I have attached an image with these dimensions labeled…

view full answer...

Answer 6

I just spoke with my rep at B&W Hitches, the B&W Pintle Hook Mounting Plate item #BWPMHD14004 is 1/2" thick.

view full answer...

Answer 7

The mounting holes of the Curt Pintle Hook, part #C48200, are spaced apart 3-1/2 inches horizontally and 1-3/4 inches vertically. I've attached a diagram for you.

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...