Tool Box Fit for 2000 Ford F-250 Super Duty with 6-3/4 Foot Bed

Question

Question:

I have a 2000n ford F250 superduty short bed and I am wondering if it is possible that this toolbox will fit my truck. If not, what would I need to modify to make it fit. thanks

asked by: Tom

0

Expert Reply:

I have a couple of toolbox options for you, but the DeeZee Red Label 5th Wheel Toolbox # DZ8560WB is not confirmed to fit your 2000 Ford F-250 Super Duty with 6-3/4 foot bed. Likely the reason this toolbox is not confirmed to fit your vehicle is due to the width of the box. Since you have a short bed, the # DZ8560WB toolbox will likely interfere with the location of the 5th wheel bed rails.

One of the largest toolboxes that is confirmed to fit your F-250 is the DeeZee Red Label Truck Bed Toolbox, Deep, Crossover Style # DZ8170DB. This toolbox measures 69-3/4 inches long x 20 inches wide x 18-1/4 inches tall, with a capacity of 12 cubic feet. This toolbox will sit 5 inches above the bed rails.

I have attached a link to all of our toolboxes that are confirmed to fit your 2000 Ford F-250 Super Duty 6-3/4 foot bed.

expert reply by: Victoria B

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 5

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 10

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 11

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 12

Installing ta Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Adapter Pin Box like the #325-GH-8045 would not void the warranty of your camper, and Gen-Y makes some of the most durable parts on the market. I really like this as an alternative to…

view full answer...