Does The Redline Wet Equalizer Bolt, # 126B2, Come In Different Lengths

Question

Question:

I need this type of wet bolt in two sizes 3 and 2.5. I need these lengths NOT including the head of the bolt or the threads. And, both size wet bolts need to be 9/16. Do you have two part # that fit this need?.

asked by: Brian M

0

Expert Reply:

I called the supplier (Redline) and they said the only wet bolt they offer in a 9/16 inch diameter is the Redline Wet Equalizer Bolt, # 126B2. The length of this bolt, not including the head of the bolt or the threads is 2-5/16 inches.

The only other wet bolt we offer is the Redline Wet Equalizer Bolt, # 126A1, which is a 3-1/2 inches length with a 3/4 inches diameter.

expert reply by: Jeff D

0

Answer 1

The 2-3/8" measurement you are referring to on the CE Smith U-Bolt Kit part #CE23002 is in regards to the diameter of trailer axle that the kit is designed to be used with. The actual width of the u-bolt from the inside edge of each bolt is…

view full answer...

Answer 2

The part #APUBR-1 is available through us. It is a U-bolt kit for 3,500 lb axles like what you have which are rated for 3,500 lbs.

view full answer...

Answer 3

So long as other dimensions match, you can replace your 2 inch wide leaf spring with the narrower 1-3/4 inch leaf spring, though if you have any added movement with the narrower spring, which is possible, you will want to change out your hangers as…

view full answer...

Answer 4

Based on your previous order, you will want the Wet Equalizer Bolt with Castle Nut and Grease Zerk - 4-11/16" Long - 7/8" Diameter #TRFA71063. This is compatible with the center #29-5-1.

view full answer...

Answer 5

We do not have a part number for a push in sleeve on the Equalizer for 2" Wide Slipper Springs item #E4541-Z because it is not made for one. This equalizer uses wet bolts like item #TRFA71063 which you then fill up with grease.

view full answer...

Answer 6

Equalizer bolts, like the TruRyde Wet Equalizer Bolt, #TRFA71063, should be torqued to yield. Equalizer bolts are not given a specific torque rating because they should allow some movement of the equalizer. If they are torqued down too tight, the…

view full answer...

Answer 7

The center hole for equalizer #TREQ1304 is 7/8 inches in diameter. The closest match we have to a bushing that will reduce that is #TRBU11568 which has a 7/8 inch outer diameter and 9/16 inch inner diameter. But it is 1-3/4 inches long so it will…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 11

The torque requirements for leaf spring u-bolts depend on the diameter of the u-bolts that are being used. If the gross weight of your tandem axle trailer is 7,000 lbs, then you likely have two 3,500 lb axles. Typically 1/2 inch diameter u-bolts are…

view full answer...

Answer 12

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Does The Redline Wet Equalizer Bolt, # 126B2, Come In Different Lengths

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching