Recommended Wet Bolt for 2 Inch Wide Equalizer Slipper Springs

Question

Question:

i was wondering if you had a part# for the push in sleeve that goes into the welded bushing on part# e4541?

asked by: John L

0

Expert Reply:

We do not have a part number for a push in sleeve on the Equalizer for 2" Wide Slipper Springs item # E4541-Z because it is not made for one. This equalizer uses wet bolts like item # TRFA71063 which you then fill up with grease.

expert reply by: Jerred H

0

Answer 1

The leaf spring part #e28SR is a 5,000 lb capacity trailer leaf spring that measures 25-1/4 inches long. The biggest factor with picking out leaf springs is to go with the spring that matches capacity first and then length second as hangers can be…

view full answer...

Answer 2

The Bronze Bushings - Qty. 4 #K71-291-00 will work well with the wet bolts #34007-187-00 which are 3-5/8 inches long. The usable length is 2-1/4 inches which will work well with the bronze bushings that are 1.74 inches long. The neverfail bushings…

view full answer...

Answer 3

The center hole of the #E4541-Z that you referenced has a metal bushing and is 7/8 inches in diameter. Because of that you would not need an additional bushing to run a 7/8 in diameter bolt.

view full answer...

Answer 4

The center hole for equalizer #TREQ1304 is 7/8 inches in diameter. The closest match we have to a bushing that will reduce that is #TRBU11568 which has a 7/8 inch outer diameter and 9/16 inch inner diameter. But it is 1-3/4 inches long so it will…

view full answer...

Answer 5

Based on your previous order, you will want the Wet Equalizer Bolt with Castle Nut and Grease Zerk - 4-11/16" Long - 7/8" Diameter #TRFA71063. This is compatible with the center #29-5-1.

view full answer...

Answer 6

Equalizer bolts, like the TruRyde Wet Equalizer Bolt, #TRFA71063, should be torqued to yield. Equalizer bolts are not given a specific torque rating because they should allow some movement of the equalizer. If they are torqued down too tight, the…

view full answer...

Answer 7

The 2-3/8" measurement you are referring to on the CE Smith U-Bolt Kit part #CE23002 is in regards to the diameter of trailer axle that the kit is designed to be used with. The actual width of the u-bolt from the inside edge of each bolt is…

view full answer...

Answer 8

I called the supplier (Redline) and they said the only wet bolt they offer in a 9/16 inch diameter is the Redline Wet Equalizer Bolt, #126B2. The length of this bolt, not including the head of the bolt or the threads is 2-5/16 inches. The only other…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 12

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Recommended Wet Bolt for 2 Inch Wide Equalizer Slipper Springs

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching