Can the Fulton Fast-Lok Coupler F346000301 be Welded On

Question

Question:

This says its a bolt on, but can it be welded?

asked by: Eric

0

Expert Reply:

Yes, if you wanted to weld the # F346000301 to your trailer you could. Since this has a corrosion resistant coating you would want to do this in a very well-ventilated area though.

expert reply by: Jameson C

0

Answer 1

For most boat trailers, it's okay to use powder coated steel wheels but this is mostly for freshwater. I am not saying you can't use powder coated steel wheels on a boat trailer in saltwater but it's really not the best option for…

view full answer...

Answer 2

The Kenda Karrier ST175/80R13 Radial Tire and Wheel #AM31990 that you referenced does not come balanced but it also doesn't need to be. Trailer tires are built and ride much differently on the road than standard passenger tires. Because of the…

view full answer...

Answer 3

I was able to confirm your wheels are 13 inches on your Zieman J1-B trailer. Because I don't know the tires currently on your trailer, I can only make recommendations for your spare based on best options for the two bolt patterns. If you have a 5…

view full answer...

Answer 4

I went out to the warehouse to measure the square holes in the Trailer D-Ring Tie Down, #LRB1. According to my measurements it will accept bolts no larger than 7/16 inches in diameter. A 3/8 inch bolt would probably be the most ideal size to use.

view full answer...

Answer 5

Trailer axles are designed to have the bow in them that you described. This allows the axle to flatten out when it is loaded and have the proper camber. If you have axles that are rated for considerably more than what the trailer will ever have…

view full answer...

Answer 6

The Fulton Fas-Lok Coupler - 2" Ball - 3" Channel - 6,000 lbs #F346000301 you referenced has a 2 inch ball and fits a 3 inch channel. The holes are measured on center at 3 inches apart. The holes will be 1 inch on center from the top and…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The 235/80R16 size tire, like the Karrier ST235/80R16 Radial Trailer Tire #AM34903, will measure about 30.8" for overall diameter and have a section width of 9.25". This tire/wheel combo has an 8 on 6-1/2" bolt pattern. If you need a…

view full answer...

Answer 12

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...