Where Does a Brake Controller Plug Into on a 2014 Toyotas Tundra

Question

Question:

Where is the trailer brake controller port located on a 2014 Toyota Tundra with towing package?

asked by: Chad

0

Expert Reply:

On your 2014 Toyota Tundra the brake controller port should be located above and to the left of the emergency brake pedal. It is possible though that it is tucked up further or it could have fallen being the driver's side kick panel next to the emergency brake. I have included a picture and video that should help.

expert reply by: Michael H

0

click to enlarge

Answer 1

I believe that the photo you sent in is of the OBD-II port on your 2014 Toyota Tundra. This is useful if your vehicle is throwing codes but it is not used for the brake controller. As long as your Tundra has the factory 7-Way at the rear of the…

view full answer...

Answer 2

The brake controller port for the 2015 Toyota Tundra is located behind the section of the dashboard with the tow/haul button. To reach the connector you will need to locate the notch in the access panel in the center of the dash near the driver's…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

The Bargman LED, Recessed, Double Taillight #47-84-527 is designed to go on either the left or the right side of your trailer. You would wire it up to the trailer wiring by function. So, if you were installing this on the driver side of your trailer…

view full answer...

Answer 12

The different size Equal-I-Zer systems have heads to match the bar sizes so the parts are not interchangeable. But not to worry, with some adjustment you can soften it up a little and not have to use a different system. You will need to lower the…

view full answer...

Where Does a Brake Controller Plug Into on a 2014 Toyotas Tundra

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching