Brake Controller Installation on 2005 Jeep Grand Cherokee w/ OEM 7-Way Trailer Connector

Question

Question:

Is there a plug and play adapter to connect a Tekonsha Brake Controller into a 7 Pin Wiring Harness that is part of a factory installed Trailer Tow Group IV installed on a 2005 Jeep Grand Cherokee Limited with a 5.7 liter hemi?

asked by: Patrick M

0

Expert Reply:

Since your Grand Cherokee is equipped with the factory 7-way trailer connector (if it says Mopar on the flap covering the 7-way, it's the factory connector), the brake controller connection has been partially wired, but there isn't a plug and play option for installing a brake controller.

Jeep will have ran the brake controller output circuit from under the dash on the driver's side back to the 7-way. Look for a coiled up blue or light green wire located near the emergency brake pedal or behind the kick panel. Sometimes the wire is located on the firewall behind the carpet.

To install the controller, you'll need a # 5506 wiring kit. You will need to run the black wire on the controller to the positive battery terminal vial a 30-amp circuit breaker included in the kit and the white controller wire to the negative terminal. The blue controller wire would connect to the wire you found that runs back to the 7-way. The red wire connects to the brake stoplight switch located atop the brake pedal. Use a circuit tester like part # PTW2993 and probe all the wires exiting the switch, looking for the wire that only shows power when the brake pedal is pressed (likely a white wire with a tan stripe). Once you find the correct wire, use a quick splice connector like # SWC502905-1 to splice the red brake controller wire into it.

I've linked you to an installation video showing a brake controller being installed on an older Grand Cherokee that has the factory 7-way. The procedure shown would be very similar for your vehicle.

expert reply by: Mike L

0

Answer 1

To install a brake controller in your 2006 Jeep Liberty with a factory 7-Way you will need to hardwire the wires from the back of the brake controller to the vehicle. This vehicle does not have a brake controller port that you can plug the brake…

view full answer...

Answer 2

You are correct that there is a green wire exiting the brake controller connector under the dash of your 2005 Jeep Grand Cherokee. The problem is that since your vehicle is not equipped with the tow package the wire is terminated somewhere inside the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 9

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...