Anti-Rattle Device Recommendation for a 2 Inch Hitch

Question

Question:

Just want to make sure the XL Anti rattle hitch lock part #SHP2040-XL will work with my 2inch Stock Ford Receiver

asked by: Joe F

0

Expert Reply:

I have a solution for you, but the part # SHP2040-XL that you referenced is designed for 2-1/2 inch hitches so I would not recommend it for your 2 inch hitch. For the version of this device designed to fit 2 inch hitches you would want the part # 63232 instead.

expert reply by: Jameson C

0

Answer 1

The XL Anti-Rattle Trailer Hitch Receiver Lock, part #SHP2040-XL is designed to fit 2-1/2 inch trailer hitches that use a 5/8 inch pin. I have attached a product review video that shows how this receiver lock is installed you can check out.

view full answer...

Answer 2

The #SHP2040-XL can be used on a 2" hitch; in fact the linked demonstration video shows it being used in a 2" hitch though it should be noted that it has an overall length of 6-3/4" and an inside pin length nearly 1 inch longer than…

view full answer...

Answer 3

The #SHP2040-XL will work with most 3 inch receivers as long as the overall width of the receiver tube measured at the hitch pin hole isn't greater than 3-1/2 inches. If your receiver meets that requirement, the #SHP2040-XL will help prevent your…

view full answer...

Answer 4

I recommend taking a look at the XL Anti-Rattle Trailer Hitch Receiver Lock, #SHP2040-XL. This is designed for use with a hollow shank ball mount and will help to reduce the "rock and roll" that you are experiencing. I have included a short…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Anti-Rattle Device Recommendation for a 2 Inch Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching