Troubeshooting Uneven Tension on Curt Weight Distribution System # 17302
Question:
I saw a question about passenger side of curt wd hitch having more tension than drivers side. I have the same problem plus the clip on top that you lift to put the trunion bar in pops out when I back my trailer in. The last time it popped out, the trunion bar fell out on the ground. It makes a loud pop when it comes out. so far Ive been lucky on finding this clip on the ground. 17302 is my hitch model. Any suggestions ?
asked by: Wayne L
Helpful Expert Reply:
I spoke with my contact at Curt and he said a couple of things could cause the uneven tension on your Curt weight distribution system # 17302. First make sure you are on even ground when you set up your system and not on an incline or that your trailer is crooked. Next, make sure you have the same number of links in on both sides of the system, with a minimum of five links.
You can test the tension in the system by taking the chains off your system an d lifting the bars until you feel tension. If the bars are at different heights when you feel tension then you have a problem with the head, casting or knuckle. You will then want to check the angle of the head.
If, when backing up, you are turning too sharply, you could be putting too much pressure on the mounting brackets and this could cause the pin to pop out. Putting that much pressure on the brackets is not recommended.
Product Page this Question was Asked From
Curt Trunnion Style Weight Distribution System with Shank, 1,000 lbs. TW, 10,000 lbs. GTW
- Weight Distribution Hitch
- WD Only
- No Sway
- Includes Shank
- Electric Brake Compatible
- Surge Brake Compatible
- Fits 2 Inch Hitch
- 800 lbs
- 900 lbs
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Q&A: Converting RV From 30 Amp To 50 Amp
- Q&A: Troubleshooting LED Lights Not Working On Trailer
- Q&A: Load Resistor Recommendation for Use with LED Tail Lights on a Flat Bed Truck with Hyperflash
- Shop: MORryde Shock Absorbing Suspension Equalizers for Tandem Axle Trailers w/ 35" Wheelbase - 8K
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 5 Bolt Flange - 7,000 lbs
- Q&A: How To Measure To Make Sure The MORryde CRE3000 Equalizers Will Fit Your Trailer
- Shop: Trailer Hitch
- Search Results: leaf springs
- Article: Trailer Tire Sizing
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 3-1/8" Long Shackle Straps
- Article: How to Accurately Measure Trailer Leaf Springs
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
- Search Results: leaf spring
- Article: Trailer Wiring Diagrams
- Q&A: How Do I Measure Axle Spread for Upgrading The Trailer Equalizers?
- Search Results: equalizer
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps
- Shop: Suspension Enhancement
- Shop: Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links
- Search Results: morryde
- Shop: Brake Controller
- Article: Double-Eye Trailer Suspension System Review
- Q&A: How to Measure Trailer Leaf Spring to Find Correct Replacement
- Video: Review of MORryde Trailer Leaf Spring Suspension - Spring Mounting Hardware - MR46ZR
- Video: MORryde Tandem Axle Trailer Suspension Upgrade Kit Installation
- Search Results: fender
- Shop: Base Plate for Tow Bar
on Weight Distribution Hitch
