Trailer Brakes Lock Up No matter What Setting is On the Brake Controller in a 2014 Ram

Question

Question:

I had my trailer brake installed on my 2014 ram truck and my brakes on my trailer are still locking up no matter what I put the setting on

asked by: John S

0

Expert Reply:

Usually when electric trailer brakes lock up it is because the brake pin on the trailer side connector is getting constant power. If you are using a 6-Way trailer connector or a 7-Way to 6-Way adapter then the likely cause is that the 12 volt circuit and the brake output circuit are switched.

This switch happens because there are 2 ways a 6-Way can be pinned out. The center pin will either be 12 volt power or electric brake output. If you are using a 6-Way or adapter for a 6-Way all you have to do is swap the wire positions for the 12 volt and brake output circuits.

Also, make sure you are using the correct Curt harness if using a Curt brake controller, # C51453.

If the harness is correct and you are not using a 6-Way or adapter then there are some tests you can perform to determine where the problem is. In the truck cab you will need to sever the blue wire several inches from the back of the controller. Then use a meter such as # PT89ZR to test the end of the blue wire coming out of the controller. It should only show amperage draw when you apply the manual override. If it shows amperage draw at idle then there is something wrong with the controller and it will need to be replaced.

If it tests fine then reconnect the blue wire. Then move on to the truck side trailer connector. Many times, dirt or corrosion can cause a short in a trailer connector. Make sure the truck and the trailer side connectors are clean and free of corrosion inside and out.

You can test the brake output pin and it should only show amperage with the manual override. If it shows power any other time then there is a short somewhere between the connector and the brake controller you will need to track down.

If the truck side checks out fine then it could be the wiring to the brake magnets or the magnets themselves. Inspect the power wires to the magnets and look for pinched, frayed, or damaged wires and fix as needed. Make sure the ground wires are attached to clean and corrosion free bare metal surfaces.

You can visually inspect the magnets and if you can see the copper windings coming through the magnets will need to be replaced. To further test the magnets you can follow the help article I have linked. I have also included some help articles on testing and troubleshooting brake controllers for you.

expert reply by: Michael H

0

Answer 1

A trailer brake controller should never smoke up like how you described. The first thing you will want to do is determine what caused this, so it doesn't happen again when towing a trailer. The most likely culprit is an internal short on the…

view full answer...

Answer 2

To install a hitch on your 1995 Toyota HiAce van you'll need to use a universal option like the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-07 which comes with a 44" wide crosstube and mounting brackets that you weld…

view full answer...

Answer 3

There are a few things that can cause the brakes to lock up on a trailer. First, disconnect the trailer from the vehicle. Then use a circuit tester like #PTW2979 if needed to test the connector on the vehicle. Have someone sit in the truck and run…

view full answer...

Answer 4

This is not a brake controller we carry, so we are not at all familiar with it, meaning I can only offer some general troubleshooting to try, independent of this controller. For locked up trailer brakes the main cause is often an incorrect stoplight…

view full answer...

Answer 5

First of all did this problem just start happening? If the trailer has always worked fine before on the same truck then it's likely a short on the trailer's brake wiring. I would start by cleaning the connector and make sure it's free of…

view full answer...

Answer 6

Yes, the Blaylock EZ Jack and Wheel Chock part #EZ-JACK can be used on a triple axle trailer like you have but you would need to turn the curve up, opposite the wheel, and drive up on the jack and you will be able to change the tires. Otherwise the…

view full answer...

Answer 7

Unfortunately that is typical issue on a Ram 3500. There are many forums that talk about this. There is a fuse that you should check F30 that sometimes causes this issue. Next use a circuit tester like #PTW2993 to test the 5 o'clock pin which…

view full answer...

Answer 8

This isn't the first time I've heard of this type of issue. It sounds like the functions of your trailer wiring are not synced with your truck. Because you have used two trucks, the issue appears to be with the trailer. I've attached a…

view full answer...

Answer 9

The problem you describe of your brake controller displaying an error message when your tow vehicle lights are turned on suggests several possible causes. One potential cause is damage/corrosion in the trailer connector(s) that could be causing two…

view full answer...

Answer 10

The Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ram #3024-P will snap directly onto a plug under the dash of your 2018 Ram 3500. Once it is snapped onto that plug, it will then need to be snapped into the port on the back of the…

view full answer...

Answer 11

It does sound like there is a possible short with the brake magnets on your trailer, especially if all the wiring looks good between the brake controller and vehicle connector. I recommend first making sure that each magnet has one wire secured to…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...