Troubleshooting Trailer Brake Controller Circuit that Activates all of the Time

Question

Question:

Vehicle: 2008 Subaru Tribeca I just purchased and installed the Curt Triflex C24VV with the Universal Brake Control Adapter and the ETBC7. After installing I used the provided tester and tested everything at the 7-way connector plug. The turn signals, running lights, break lights, and power all work fine BUT the electric brake pin position #2, blue wire as shown in the ETBC7 installation guide back diagram has power even without the brakes engaged. It only goes off if I unplug the break controller. I first questioned the cold side break switch wire but verified this wire by disconnecting the break controller at the adapter and tested the corresponding break switch pin red wire at the break controller adapter and it turn on only when I pressed on the break. The break controller seems to power up fine. The single dot comes on and goes off after 10 to 15 minutes just like the installation guide says it should. Any suggestions why I am getting constant power to the electric brakes at the 7-way? I have checked and double checked all my wiring and can not find anything wrong. You can also call me at

asked by: Dave C

0

Expert Reply:

You said that the brake controller output circuit was the number 2 circuit on your 7-way. If by that you mean the 2:00 position then you have the circuits flip flopped. The 2:00 position should be the 12 volt accessory circuit, not the brake output circuit. That would explain why you are getting 12 volts all the time.

The brake controller circuit should be the 5:00 position. Check out the diagram I attached to see how it should all get wired up.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hello Dan, I can definitely help with this. It is completely normal for the Curt TriFlex brake Controller #C24VV to show the current gain setting when the brakes are applied, or when the manual override is pressed. It sounds like you have the gain…

view full answer...

Answer 7

The bouncing feeling you are describing is not caused by improper installation of your weight distribution system. This is actually an adverse effect of the system. The ride on your 2017 Ram 1500 has become more stiff in the rear as a result of the…

view full answer...

Answer 8

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 9

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 10

For your 2019 Ram 1500 the Curt TriFlex NEXT Trailer Brake Controller item #C24VV can be installed with a plug and play adapter using the Curt Custom Wiring Adapter item #C51458. The port you need is right above where your right foot would be covered…

view full answer...

Answer 11

There is an extremely simple trailer hitch installation for your 2020 Ram 1500, the Curt Trailer Hitch #C13419 which you can reasonably expect to install in less than 15 minutes. All you really have to do is remove the plug from the bumper step, put…

view full answer...