Distance from Hitch Pin Hole to Weld Gusset on Curt Ball Mount # C45090

Question

Question:

Hi, what is the distance from the hitch pin hole to the nearest weld gusset on this c45090. I need to use it in a rise position and Im concerned that it will be too close to the bumper. thanks in advance

asked by: Tan

1

Helpful Expert Reply:

On the Curt Ball Mount # C45090 the distance from the center of the hitch pin hole to the near edge of the reinforcing gusset is 3-inches. From the hole center to the end of the shank the measure is 2-1/2-inches. I prepared a photo diagram for you to show these dimensions.

I also linked our main page for all 2-inch ball mounts.

expert reply by: Adam R

1

click to enlarge

Answer 1

It sounds like you are asking about the distance from the center of the hitch pin hole to the back of the shank of the ball mount that slides into the hitch. That distance is 2-1/2 inches. I attached a picture that shows this dimension as well.

view full answer...

Answer 2

I do have an option for you but none of the dual hitch adapters that provide adequate drop can be used for towing. Instead, you'd need to go with a standard ball mount with the drop you need like the Curt Ball Mount part #C45090. Then, you…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Distance from Hitch Pin Hole to Weld Gusset on Curt Ball Mount # C45090

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching