Trailer Light Kit Recommendation for a Pace Enclosed Trailer

Question

Question:

I have a Pace 6.5x10 2004 enclosed trailer and I need the oval tail lights and the trailer wiring kit for this

asked by: Jeff

0

Expert Reply:

For an LED trailer wiring kit that would work well on your Pace trailer I would recommend the part # TLL16RK. This part number comes with everything. The lights are rectangular though.

To use the part # ST70RB you would need the grommets part # a70gb, the pigtail part # A45PB, brackets part # BK70BB, and # A35W42B.

expert reply by: Jameson C

0

Answer 1

You will need four each of the Sealed, 6-1/2 inch Oval LED Trailer Stop, Turn and Tail Light, 48 Diode, item #STL70RB, Rubber Grommet for 6-1/2 inch Oval Trailer Tail Lights, item #A70GB, and either the Straight 3-Wire Pigtail, item #A45PB or the…

view full answer...

Answer 2

The largest license plate bracket we offer is the Optronics Enclosed Cargo Trailer License Plate Holder, part #LP35BB. This bracket measures 14-1/4 wide x 8-5/16 inches tall. This is mounted with 4 screws(sold separately) and 2 screws are needed to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...