How to Install Spring Bars Using Bolt On Brackets for a Curt Weight Distribution System

Question

Question:

with the battery tray in the way of the over the rail style brackets ive ordered the side bolt on style.Im unsure of how to attach the chains to them w tension as the brackets that came w my hitch you would pry up w the pry bar how do you get the correct tension with the bolt on side brackets?

asked by: Mike R

0

Expert Reply:

When using the bolt brackets # C17005 you will have to use the trailer jack to lift both the trailer and the tow vehicle to be able to put the spring bar on or take them off. Since the bolt-on brackets do not have lift assembly like the normal brackets, this is the only way to install/remove the spring bars.

expert reply by: Michael H

0

Answer 1

The Curt MV Weight Distribution System part #C17050 does not have sway control so reversing is not as big of an issue although the trailer still needs to remain relative straight. If you need to turn and backup it is recommend to unhook the spring…

view full answer...

Answer 2

I spoke with Curt and spring bars of the WD system #C17150 has an overall length of 30-5/8 inches and the diameter is 1-1/4 inches where it fits into the head. The length is measured from the center of the end that fits in the head to the center…

view full answer...

Answer 3

The Curt Chain Hangers for the Curt Weight Distribution Systems would be exactly what you need for your A-frame trailer that does not have clearance above the frame rail because of your propane tank and battery support. I can also assure you that…

view full answer...

Answer 4

Yes, the dimension you mentioned is the distance from the center of the ball hole on the coupler back on the frame rails 27-30 inches for the Fastway e2 part #FA92-00-0600.

view full answer...

Answer 5

I have the perfect option for you to install a weight distribution system on your trailer with limited tounge space. This option consists of the Reese Pole-Tongue Adapter for Weight Distribution Systems part #RP58393 and a Reese Steadi-Flex Weight…

view full answer...

Answer 6

Assuming you're talking about the length of your shank being 16" long, then no the length of your shank will not affect the capacity of your weight distribution system. That being said, if you're looking for a complete system I recommend…

view full answer...

Answer 7

The first step in choosing a weight distribution system is to conclusively determine the tongue weight of your camper once it is fully loaded and ready to tow. This includes full water and propane tanks plus any other gear you would typically travel…

view full answer...

Answer 8

You are doing it correctly. The only way to get the proper tension on/off the spring bars when using chain hangers #C17005 is to use the trailer jack. This often means that you have to lift up the trailer/truck a good amount before you can attach the…

view full answer...

Answer 9

The spring bar length in Curt weight distribution system #C17051 is 30-5/8 inches long. This will put the system outside the range you need but I do have a way to make it work with your trailer. Instead of using the lift brackets that come with the…

view full answer...

Answer 10

We offer a Bolt On Weight Distribution Chain Hanger Kit, part number RP58305. This would allow you to locate the bracket where you need it, and because it would bolt to the side of the trailer tongue, it would not interfere with your propane bottles.…

view full answer...

Answer 11

With Curt Short Arm weight distribution systems like the part #C17322 that you referenced the distance from the center of the hitch ball to the far edge of the chain hanger will be 30-5/8 inches. A lot of times the best solution for V-nose trailers…

view full answer...

Answer 12

With your Blue Ox SwayPro Weight Distribution w/ Sway Control #BXW1500 the rough ride and bucking could be from a couple of variables. If you have weight behind the rear axle of your truck, you may need a larger weight distribution system because…

view full answer...

How to Install Spring Bars Using Bolt On Brackets for a Curt Weight Distribution System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching