Propane Tanks Interfering with Weight Distribution System Take Up Brackets
Question:
Hi, my name is Josh. I have a 2004 31 Flagstaff by Forest River. I baught a Curt Manufacturing Trunnion style Weight Distribution hitch from the guy who I purchased this camper from, although he had never installed the hitch on the truck or the trailer. I have a 01 Dodge 2500 that I am planning on pulling it with. I purchased a new shank for my truck because it sat too high, and put the original head on the new shank. I hooked the truck to the camper and put the spring bars in place, and I looked at the spring bars, and they seemed to be to long. Where they came to the frame of the camper is right where the propane tanks are, therefore I have no place to mount the brackets on the trailer above the spring bars. Do they make shorter spring bars??? And if so, do you have them to fit my Curt Manufacturing shank head??? Any help would be appreciated. Thank You.
asked by: Josh
Expert Reply:
We offer a Bolt On Weight Distribution Chain Hanger Kit, part number RP58305. This would allow you to locate the bracket where you need it, and because it would bolt to the side of the trailer tongue, it would not interfere with your propane bottles. I will include a link to the Hanger Kit, which can be found below.
![Mike L](https://images.etrailer.com/static/images/catg/people/166_tn.jpg)
Products Referenced in This Question
Chain Hangers for Reese Weight Distribution Systems - Bolt On
- Accessories and Parts
- Weight Distribution Hitch
- Chain Hangers
- Reese
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Chain Hangers for Reese Weight Distribution Systems - Bolt On
- Shop: Reese Pro Round Bar Weight Distribution w/ Sway Control - 11,500 lbs GTW, 1,150 lbs TW
- Shop: Curt MV Weight Distribution System w/ Friction Sway Control - Round Bar - 10K GTW, 1K TW
- Article: Big Truck Big RV
- Q&A: Moving Propane Tank Bracket On a Travel Trailer For Fastway e2 Weight Distribution to Fit Properly
- Video: Reese Weight Distribution System Chain Hangers Installation
- Shop: Brake Controller
- Shop: Replacement Round Spring Bar for Fastway e2 Weight Distribution Systems - 1,000 lbs TW
- Shop: Threaded Rod for 30-lb LP Gas Tanks
- Shop: Chain Hangers for Curt Weight Distribution Systems - Bolt On
- Search Results: rp58305
- Q&A: Trailer Propane Tanks and Batteries Interfere with Lift Brackets on Curt Weight Distribution System
- Search Results: 15x6 5x5.5 rim and tire
- Shop: Curt Spectrum Trailer Brake Controller - Dash Mounted Knob - 1 to 4 Axles - Proportional
- Video: Ultra-Fab Trailers and RV Leveling Blocks Review
- Q&A: Upgraded Round Springs Bars for Draw-Tite 750 lb Round Spring Bars 81518 for WDH
- Shop: RV Power Cord
- Shop: RV Electrical
- Q&A: Chains for Weight Distribution System are Too Short for Tall Trailer Frame
- Q&A: Can Weight Distribution Chains Hang at an Angle or Do They Have to be Straight Up and Down
- Video: Review of Ultra-Fab Products Trailer Jack - A-Frame Jack - UF38-944040
- Video: Phoenix Electric A-Frame Trailer Jack Review
- Video: JR Products Gas Tank Threaded Rod Review
- Shop: Trailer Hitch
- Shop: RV Exterior Lighting
- Video: Review of Fastway Weight Distribution Hitch - e2 800 lbs TW WD With Sway Control - FA94-00-0800
- Video: Curt Weight Distribution - WD With Sway Control - C17322 Review
- Q&A: Can Sway Control be Used on a Trailer without Using Weight Distribution
- Q&A: Wiring Diagram for Dometic Single Zone Thermostat and Control Box
- Article: 5 Things to Know About Weight Distribution Hitches