Will the Longview Mirrors part # LVT-3100C Allow Power Mirrors to Fold

Question

Question:

Will these interfere with the folding of power mirrors on ram 1500/2014

asked by: Don

0

Expert Reply:

I spoke with my contact at Longview and she said Custom Towing Mirror Set # LVT-3100C will fit the stock OEM side view mirrors on the 2014 Ram 1500 with the power folding feature. Your mirrors would be able to fold just fine with these installed.

See picture that I attached plus install video.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Longview Custom Towing Mirrors part #LVT-3100C that you referenced have been confirmed to fit the 2015 Ram 1500 so they would work well for you. Check out the install video I attached as well.

view full answer...

Answer 2

Yes, the Longview Tow Mirror part #LVT-3100C that you referenced does fit your 2016 Ram 1500. I attached an install video that shows the mirror set installed on a 2016 Ram 1500 just like yours for you to check out as well.

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...