What Metal is the Rapid Hitch Trailer Hitch Lock # AM3492 Made of

Question

Question:

Are the ends made of stainless steel or are they aluminum?

asked by: TheTexasR.A.T.

1

Helpful Expert Reply:

I went and pulled a Rapid Hitch Trailer Hitch Lock # AM3492 from our warehouse and determined that the ends of the locks are aluminum and the middle section is stainless steel.

expert reply by: Jameson C

1

Answer 1

The Rapid Hitch Trailer Hitch Lock and Adjustment Pin Lock Set, part #AM3492, that you referenced, is listed with a 10,000 lb weight capacity. That weight capacity would have plenty of strength when using it to tow your vehicle.

view full answer...

Answer 2

I assume that you are wanting a 3 inch rise or drop ball mount for your factory installed 2012 Toyota Tundra with a factory installed Class IV hitch that has a 2 inch receiver. You have indicated that you would prefer a ball mount that is made of all…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 12

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

What Metal is the Rapid Hitch Trailer Hitch Lock # AM3492 Made of

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching