Mounting Hole Dimensions for the 55" Lock Side-Door Bar Lock Assembly # 3057-55

Question

Question:

what is the length between the top hole and bottom hole on your 55inch pipe Lock Side-Door Bar Lock Assembly. Also what is the measurement on the lock handle to the top hole of the hinge. thanks

asked by: Randy S

1

Helpful Expert Reply:

I went and pulled a 55" Lock Side-Door Bar Lock Assembly # 3057-55 from our warehouse to get the dimensions you requested. The length from the top mounting hole of it down to the bottom mounting hole is 53-1/2 inches, the distance between the holes of the mounting brackets is 3-1/4 inches, and the distance from the center of the handle to the top mounting hole is 26-3/4 inches.

expert reply by: Jameson C

1

click to enlarge

Answer 1

If you have a bar style door like the part #3057-55 that you referenced on your trailer you could pretty easily replace it with the #3057-55. The hinges may match up but we don't know that for sure. You can check out the picture I attached that…

view full answer...

Answer 2

While we do not have any specific replacement parts we do have some options but you will need to replace the latch system (unfortunately the second picture you mentioned did not come through). For example, you may be able to use the 55" Lock…

view full answer...

Answer 3

I went and measured the mounting bracket of the 55" Lock Side-Door Bar Lock Assembly #3057-55 that you referenced and found that the actual bracket is 1-1/4 inches wide, but if you count the hinge portion that sits a bit above bracket the…

view full answer...

Answer 4

The handle keeper for 55" Lock Side-Door Bar Lock Assembly #3057-55 has mounting holes spaced 4 inches apart on center. The keeper itself can be positioned after the hinges and bar are installed.

view full answer...

Answer 5

Yes, you can use the lock side-door bar lock assembly, #3057-55, on a door hinged on the left or right. Just flip 'er over as needed! This version features a 55 inch long pipe. If you need a shorter version use #305736 with a 36 inch long pipe.

view full answer...

Answer 6

The 55" Lock Side-Door Bar Lock Assembly part #3057-55 are designed to open flat to allow you to install on the both the passenger and driver side (left and right). I have attached a very helpful video for your reference.

view full answer...

Answer 7

I do have an option for you but we don't carry Imperial products. That said, the Side-Door Bar Lock Assembly part #3057-55 would be an excellent replacement for this. The only real difference is the mounting pattern is not the same so some small…

view full answer...

Answer 8

I went out to the warehouse and pulled the Replacement Hitch Ball for B&W Turnoverball Underbed Gooseneck Hitches, part #BWGNXA2000, and took some measurements for you. The square part of the hitch ball is 4" long and 2-1/2" wide. The…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...