Suspension Products to Correct Minor Rear-End Sag in 2003 GMC Sierra 1500LD Towing 3200-lb Trailer

Question

Question:

I tow a small camper with my 2003 GMC Sierra 1500. The gross weight of the trailer is 3200lbs with a tongue weight of 400lbs +/-. When hooked up, the rear of truck s about two inches. If you didnt watch it squat, you would never know it did just by looking at it. With weights that low Ive been told weight distribution is not necessary, but the minor sag is something Im concerned about. Should I be? It seems normal to sag a little under load, but if I wanted to eliminate this sag would the super spring part # SSA5MTKT be a good option? Thanks.

asked by: Brian F

0

Expert Reply:

It is perfectly normal for the rear of a tow vehicle to sag to some degree when hitched to a trailer due to the trailer tongue weight. For this reason it is usually best to have the height of a hitch ball about an inch or so higher than the top of the trailer's coupler (when the trailer is level) to compensate for this normal sag.

The SuperSprings Custom Suspension Stabilizer and Sway-Control Kit # SSA5MTKT that you referenced fits both 2WD and 4WD versions of your truck and will help reduce sag, but these are better suited to issues with both sag and body roll. In your application, with sag being the only concern noted, there is a more cost-effective option that is also easier to install.

Timbren rear suspension kit # TGMRCK15S also fits both 2WD and 4WD versions of your Sierra and will support the rear end when under the tongue weight load from your trailer. Rubber jounce springs like these Timbrens do not affect your ride quality when you're not towing but they do instantly engage when under load to stiffen and support your truck's suspension. They are simple to install (no drilling required - please see the linked video) and carry a limited lifetime warranty.

All such kits are intended to work with a suspension system that is in good working order and none can increase a vehicle's weight capacity. The linked article will give you additional information on Timbren products.

expert reply by: Adam R

0

Answer 1

I spoke at length with my Equal-i-zer representative regarding what you have going on. We came up with a few possibilities, some or a combination of several will likely be helpful in eliminating the bounce. I believe the rear suspension of your truck…

view full answer...

Answer 2

There are a couple things that come to mind that may help with the bounce that you are experiencing when towing the 24 ft pull behind trailer with your 2014 Chevrolet Silverado 1500. I would start by checking to make sure that your trailer isn't…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Cody, you are installing this B&W Turnoverball #BWGNRK1020 on a 2021 Chevy 2500 correct? If so, the M14 bolts are definitely the correct size. It is possible that the holes in the frame are corroded which is preventing the bolts from…

view full answer...