Tapping Into Brake Light Circuit to Install Brake Controller In a 2011 Chevy Equinox

Question

Question:

how to wire electric brake controller on a 2011 equinox ,need to know how to tie in on brake pedel swtich for the control

asked by: Joe D

0

Expert Reply:

On a 2011 Chevy Equinox you cannot tap into the brake light switch to install a brake controller. You have to get the signal from the BCM (body control module). It is located up under the dash to the left of the brake pedal. There is a 26-pin connector. You need the wire in position 11. It should be a white wire.

I have included a picture that should help. I have also included a link to another answer page to the right that also has that picture.

expert reply by: Michael H

0

click to enlarge

Answer 1

Adding a charge line kit like the Roadmaster #RM-156-25 to your flat towing setup is a good idea to maintain the charge of the battery on your Equinox, but I still highly recommend pulling the #32 fuse as listed in the owner's manual. The…

view full answer...

Answer 2

We have to recommend you stick with all of the recommendations that GM makes for flat towing your 2015 GMC Terrain. If they released an update that it's important to pull the 16 fuse it's for a good reason and you should do so. To…

view full answer...

Answer 3

You should be seeing the same "Service Power Steering" and ABS warning lights/All Wheel Drive as you've seen in the video. Since you have a 4 cylinder model of the 2012 Equinox, I would make sure that you've left the…

view full answer...

Answer 4

The best and safest way to determine which wire is the cold side of the brake light switch on your 2013 Chevy Equinox is to simply test them with a circuit tester like #PTW2993. You are looking for the wire above the brake pedal that only receives…

view full answer...

Answer 5

According to Curt there is not a plug-and-play brake controller adapter for the 2019 Chevy Equinox so the Curt Venturer Brake controller would need to be hardwired in. To do this, you would need to convert the factory 4-way on the Equinox using a…

view full answer...

Answer 6

I found the installation video that we did on our 2019 Chevrolet Equinox but I have not been able to locate the video you mentioned with the 2018 Equinox. Our video we did was on a Equinox that came with the factory 7-way wiring and that may be why…

view full answer...

Answer 7

So long as a hub uses the correct bearings that match the dimensions of the spindle that is on the axle there is no worry about using two different brands of products, such as a Dexter hub on a Lippert axle. That in itself is not a concern. When a…

view full answer...

Answer 8

Can you turn the wheel by hand if it is jacked up and off the ground? It sounds like your brake assemblies are dragging too much which is creating heat from friction. To see how to adjust the brake assemblies so that you get the correct amount of…

view full answer...

Answer 9

Trailer breakaway batteries are usually rated for 5-amp-hours and are designed to keep your four brake assemblies engaged for 15-minutes in the event of an accidental disconnect. The only way the breakaway battery could heat up your drums is if it…

view full answer...

Answer 10

I would recommend completely ruling out the bearings by closely examining them and the spindle for discoloration caused by overheating. If you have determined that it is the brakes that are hot, and not the hub itself, I would recommend readjusting…

view full answer...

Answer 11

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...