7-way Recommendation to Replace a 6-Way

Question

Question:

I want to switch a 6 pole to 7 flat car end connector. What product should I use? Vehicle is a 96 F250 with a Tekonsha 2030 Mark 12 controller. Let me know. Thanks

asked by: Kevin D

0

Expert Reply:

I would recommend you cut off the 6-way you have at the rear of your truck and then install a # 50-87-004 in it's place.

I attached a couple wiring diagrams for the two styles of connectors so that you would know how to wire up the new 7-way with the wires from the 6-way.

expert reply by: Jameson C

0

click to enlarge

Answer 1

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 2

I looked up the trailer connector wiring diagram for a 2007 Ford F-250 which should be the same as a Ford F-350 and found the 7-way trailer connector to contain the following wires: Orange = 12 Volt Power White = Ground Black/Green = Reverse Blue =…

view full answer...

Answer 3

In order to determine the correct function of the wires that are included with the Ford Replacement OEM Tow Package Wiring Harness part #118242 you are going to want to plug the harness into the vehicle and have a friend sit in the cab and operate…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...