ProGrip ME-01 Cam Buckle Tie-Down Straps - S-Hooks - 1" x 6' - 400 lbs - Qty 2

See what our Experts say about this ProGrip Boat Tie Downs

• Recommended Hitch-Mount Motorcycle Carrier for Use on Class A Motorhome
  We do offer one motorcycle carrier that is properly rated for use in the 2-inch hitch on your Class A rig, Ultra-Fab Motorcycle Carrier # UF48-979033. This ramped carrier offers a 500-lb capacity. You will need to confirm the tongue weight (TW) capacity of your hitch to ensure it is rated high enough for the combined weight of your motorcycle and the 48-lb Ultra-Fab carrier. Their combined weight cannot exceed the hitch's capacity. You'll also need tie-down straps to secure the bike to...
  view full answer...
• Recommended Trailer Hitch Receiver for Motorhome for Carrying Mopeds
  Your best option for 2 mopeds on the back of a motorhome is to use the Flint Hill Goods 29" x 49" Carrier w/ 60" Ramp - 2" Hitch - 500 lbs # FHG69ZR. This is not rated for RV use, but no cargo carriers are. Then you can use the Master Lock Cam Buckle Straps w Strap Traps and Spring Clip Hooks # 317-412080 and soft loops # 06303 for each moped. If you don't have a hitch receiver on the back of your motorhome, I recommend the Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide # C13701...
  view full answer...
• Recommended Carrier for 360-lb Scooter for Use in 2-Inch Front Hitch on 2011 Ford F-250
  All of the front-mount 2-inch hitches offered for your 2011 Ford F-250 have the same 500-lb vertical load limit so this means your 360-lb Kymco scooter and the carrier you use to transport it must not together weigh more than this 500-lbs. The Ultra-Fab Motorcycle Carrier # UF48-979033 has a carrying capacity of 500-lbs which is more than enough for the GT300i, and the carrier itself weighs only about 48-lbs so this combination will work with your hitch's capacity. You'll want to take...
  view full answer...
• Scooter Carrier Recommendation for Use on the Back of a 2013 Leisure RV
  K2 Tilt Down Hitch Mounted Motorcycle Carrier # K2TMC201 is not rated for use at the back of an RV or trailer so it is not going to work for you. But we do have a carrier that is rated for RV use, it is # UF48-979033. Scooters are typically shorter in terms of wheel base compared to motorcycles so you should be able to mount the heavier end of the scooter closer to the center of the carrier which is definitely what you want to do anyway. Also I recommend over securing this set up because...
  view full answer...
• Hitch-Mount Carrier for Bicycle That Does Not Require Lifting the Bike
  Hitch mount bike racks are offered in both the hanging-style and the platform style; the latter does require the bike be lifted but to a lesser degree than hanging-style racks. We do not currently offer any bicycle racks with ramps. However, the Ultra-Fab Motorcycle Carrier # UF48-979033 that you referenced may indeed be the right solution for you. This carrier for 2-inch hitches has a ramp that can be fitted to either side of the carrier and it includes a pin and clip to secure it in...
  view full answer...
• Will Ultra-Fab Motorcycle Carrier # UF-48-979033 Haul a 2007 Honda Reflex Scooter on Dodge Ram 2500
  If the hitch you have on your Dodge Ram 2500 has a tongue weight rating of at least 500 lbs or more, then the Ultra-Fab Motorcycle Carrier, part # UF48-979033, will be able to haul your 2007 Honda Reflex Scooter on the back of your truck. The carrier has a weight capacity of 500 lbs and a length of 80 inches. It has adjustable pull pins on the carrier that can be adjusted to fit the wheelbase of your scooter. I would also recommend our Hitch Lock, part # e98882, to lock the carrier to...
  view full answer...
• Vespa Moped RV Hitch Carrier Recommendation
  Not every motorcycle carrier available is rated for the rougher ride quality that is present at the rear of an RV, but the Ultra Fab carrier part # UF48-979033 is rated for RV use and would be a great option. This carrier has a 500 lb capacity which would be more than enough for your 350 lb. Vespa. The ramp length is 39 inches. For tie-downs you may also be interested in the part # 317-412080.
  view full answer...
• Recommended Hitch Adapter to Allow Use of 2-Inch Kuat Bike Rack in Class I Hitch on 2015 Acura TLX
  Hitch adapters like # HT5R are available to allow use of a 2-inch hitch accessory in a 1-1/4-inch hitch. And this particular product also provides 5-inches of height rise to improve ground clearance. BUT...there's always one of those...use of ANY hitch adapter causes the unavoidable side-effect of reducing your hitch's rated tongue weight (TW) capacity. This loss of capacity results from the increased distance between the hitch tube and the actual rack. The greater distance means more...
  view full answer...
• Hitch and Motorcycle Carrier Use on 2006 Honda Odyssey
  Draw-Tite hitch # 75270 is a confirmed fit on your 2006 Honda Odyssey and its 675-lb tongue weight (TW) rating is plenty for the combined weight of your motorcycle and carrier application but as you noted the car itself has a lower rating. There is no way to bolt-on more capacity to this or any other vehicle. If your combined carrier and bike weight is 320-lbs then you will be just within the vehicle's rating of 350-lbs total tongue weight. Since you will be so close to the maximum, and...
  view full answer...
• Trailer Hitch And Motorcycle Carrier For Rear Of 2003 Holiday Rambler Fifth Wheel Trailer
  We do offer a frame-mounted trailer hitch that may work for your 2003 Holiday Rambler. I recommend the Draw-Tite Class IV Weld-On 62 inch Wide Ultra Frame Trailer Hitch Receiver, part # 41990-07. This is a weld-on hitch that will fit frames up to 44 inches wide. This hitch has a much higher rating at 1,600 lbs than the 350 lbs for the # 13703 you mentioned. You will want to make sure the frame of your Holiday Rambler has the weight capacity for your motorcycle. The motorcycle carrier...
  view full answer...
• Is There a Canoe Mount for the DeeZee Invis-A-Rack
  There are not specific mounts to carry a canoe on the DeeZee Invis-A-Rack # DZ951550, you can modify the cutout inside the Malone Deluxe Kayak Carrier with Tie-Downs - Foam Block Style part # MPG152 to make them work for your kayak. These pads are about 15" wide. If you need something wider, the Rhino-Rack # RRRWP03 would be a better choice at 21" long. Both of these will work to help reduce movement and keep help reduce any scratching/damage to your boat while in transit. Both of those...
  view full answer...
• Use of Hitch Extension with Flint Hill Goods Aluminum Cargo Carrier FHG69ZR
  There are a few things to keep in mind for your desired setup. First, the weight rating of the hitch on your van must be more than the combined weight of your selected carrier and two scooters. Their combined total must be within the hitch's tongue weight (TW) rating. The Flint Hill Goods Cargo Carrier # FHG69ZR weighs about 77-lbs. You can add this to the weight of your two scooters to know the total TW load that will be on the hitch. Next check the sticker on your hitch to confirm its...
  view full answer...
• Hitch Adapter to Raise Height of Cargo Carrier for Batter Ground Clearance
  We can help you with a 2-inch hitch adapter that will give you a height rise for better ground clearance with your CargoPod hitch cargo carrier. I suggest the Roadmaster 2-inch High-Low Adapter # RM-048-8. The Roadmaster has a solid steel shank for strength rather than a hollow one like the Malone # MPG544 and it gives you a full 8-inches of rise. This too will reduce your hitch's rated capacity by 50-percent, the same as the Malone, and it also shares the same 400-lb tongue weight (TW)...
  view full answer...
• Transporting Dirt Bike with Class III Trailer Hitch on 2006 BMW X3
  The Draw-Tite Class III Max Frame Receiver Hitch # 75371 referenced in your question, which is confirmed to fit your 2006 BMW X3, features a tongue weight capacity of 350 pounds. As long as you remain under this capacity with the combined weight of your carrier and dirt bike (which it sounds like you will), you will not have an issue transporting your bike. If you do not yet have a carrier, I recommend looking at the Ultra-Fab Dirt Bike Carrier # UF48-979033. This is a really nice carrier...
  view full answer...
• Shortest Adjustment Length for ProGrip ME Series Cam Buckle Tie-Down Straps # 317-412080
  I went out to our warehouse to take a look at the ProGrip ME Series Cam Buckle Tie-Down Straps # 317-412080 that you referenced. I tightened the strap all the way down and measured a length of right at 28 inches end to end from each hook. This is the shortest possible adjustment on the strap. I have included a short video review that you can check out as well.
  view full answer...
• Motorcycle Carrier Recommendation for RV to Carry Honda Rebel 250
  Not every motorcycle carrier available is rated for the rougher ride quality that is present at the rear of an RV, but the Ultra Fab carrier part # UF48-979033 is rated for RV use and would be a great option. This carrier has a 500 lb capacity which would be more than enough for your Honda Rebel 250. This carrier weighs 51 lbs which is about as light as you'll find. For tie-downs you may also be interested in the part # 317-412080.
  view full answer...
• Recommended RV Hitch and Motorcycle Carrier for 2011 Crusader 5th Wheel Trailer
  In order to use an RV-rated motorcycle carrier on the back of your 2011 Crusader 5th wheel you will first need to install a 2-inch frame-mount hitch with a 500-lb tongue weight (TW) capacity. Curt hitch # 13703 that you referenced is rated only to 350-lbs so it will not work for your intended use. The linked page will show you Curt # C13701. You'll first want to measure your 5th wheel's frame - outside to outside - to confirm this hitch will fit. Once you have a hitch in place you can...
  view full answer...
• Surco Rooftop Cargo Basket for Thule Roof Racks on Honda Fit
  The Surco Safari Rack 5.0 Rooftop Cargo Basket for Thule Roof Racks, # SPS5084-T400, will work with all Thule roof racks including racks compatible with your Honda Fit. The only problem you may encounter is in the access of your rear hatch due to the overhang. I would recommend a smaller roof rack if it weren't dependent on your painting size. This rack will fit your paintings even two of them stacked within the 5" depth of the carrier, but they will be exposed to wind and weather without...
  view full answer...
• Motorcycle Carrier Recommendation Rated for Use Behind RV
  For the weight of a motorcycle and carrier I'd recommend finding a welder/fabricator in your area to make you a reinforced hitch setup for the rear of your RV. That will be the best option our RV multi-fit hitches won't be ideal for that much weight on a carrier. For an RV rated motorcycle carrier though we have the the Ultra Fab carrier part # UF48-979033 which has a 500 lb capacity. For tie-downs you may also be interested in the part # 317-412080.
  view full answer...
• Recommended Front Hitch and Motorcycle Carrier for 2018 Ford F-350
  Starting with the front hitch for your 2018 Ford F-350 I recommend the Draw-Tite Front Mount Trailer Hitch Receiver # 65076. This is confirmed to fit your truck and will provide you with a 2 inch receiver opening and a 500 pound vertical load limit. Just note that the plastic air deflector/fascia will need to be removed for installation. It can just be left off once finished or you can trim it and reattach it with the hitch installed. I have attached the written installation instructions...
  view full answer...
• Can Motorcycle Carrier Be Mounted To Front Of A Motorhome
  The Ultra-Fab Dirt Bike Carrier for 2" Hitches - With Ramp - 80" Long - 500 lbs # UF48-979033 can be mounted to the front of a 24V View Motorhome as long as the front mounted hitch is able to handle the vertical load weight of the Honda Rebel and the carrier combined weight of 391 lbs. The only other thing to consider is the front mounting can limit your view and should not block your headlights. To secure the carrier and the bike, I recommend the hitch lock # e98882 and the ProGrip...
  view full answer...
• Concerns about Length of Shank of Ultra-Fab Motorcycle Carrier on 2001 35 Winnebago Adventurer
  The Ultra-Fab Motorcycle Carrier # UF48-979033, has one hitch pin hole, which is 16 inches to the closest edge of the carrier. This may seem far from the motorhome, but not to worry, the The Ultra-Fab carrier has been constructed, tested, and rated to carry up to 500 lbs at that distance behind a motorhome. This is the only motorcycle carrier we carry that is properly rated to be used on the rear of a motorhome. I'd also recommend the Roadmaster Quiet Hitch, part # RM-061, that will help...
  view full answer...
• Recommended Cargo Carrier for Manual Wheelchair on 2009 Ford Focus
  For your 2009 Ford Focus the hitches we carry limit the capacity to 200 lbs and Class I. So for your cargo carrier, I recommend the 19x47 Curt Cargo Carrier # C18110. This will fit the length of your manual wheelchair but you will need to collapse it to fit the width of the carrier. It will give you a steel grate to make sure your 4 wheels have a sturdy base and then you will need to secure it with straps like the ProGrip Cam Buckle Straps - 400 lbs - Qty 2 # 317-412080.
  view full answer...
• How to Carry Two Kayaks On 2015 F150 6 1/2 Foot bed With BakFlip Hard Cover
  The best way to carry 2 kayaks on your 2015 F150 6 1/2 foot bed is a ladder rack. I recommend the Pro Sport Ladder rack part # RS69FR. This works with the BakFlip tonneau cover. It also allows you to fold your cover up when you need access to the bed without interference compared to other ladder racks that are not compatible with tri-fold hard covers. The bars on the ladder are 72 inches long so you can carry both kayaks side by side. The tie downs part # A4000882 slide into the mounting...
  view full answer...
  

Do you have a question about this Boat Tie Down?