The Au-Tomotive Gold Honda Trailer Hitch Cover # AUT-HON-C does not include a pin-and-clip nor a gasket for installation. A pin-and-clip kit # C21510 is available, as is a locking anti-rattle kit # 63232 which will both prevent theft and eliminate any potential for rattle in the hitch opening. This hitch cover will easily fit in your 2-inch hitch. view full answer...
For replacement pins that hold the balls of the # C45900 to the shank of the assembly we have the part # C45925 which comes with 2 pins and 2 clips. We do not have them individually though. view full answer...
The Carpod Walled Cargo Carrier, # M2205, that you referenced will work with your 2011 Ford Edge and will not require the use of a hitch extension or adapter. I have attached a demonstration video of this carrier on a 2013 Ford Edge for you to check out.
The Edge in the video is the non Sport model and has the Draw-Tite Class III Trailer Hitch, # 75992, installed. Keep in mind, the hitch pin and clip are sold separately from the Carpod carriers. For a standard pin and clip, you can use... view full answer...
If you check out the picture I attached you can see to what degree of assembly the Viking Solutions Stack Rack II 2-Level Cargo Carrier for 2" Hitches # 310-VSR201 ships in. You can also see what pins and install hardware it comes with as well.
You will need a pin and clip as well like with part # PC3. view full answer...
Hitch locks do not have towing capacities, including the Curt Trailer Hitch Receiver Lock - 2" and 2-1/2" Hitches - Stainless Steel # C23519.
Reason is because locks (and pins & clips) do not bear weight in the same manner as hitches or ball mounts, for example. So you just need to follow the capacity of the hitch or ball mount (whichever is lower). view full answer...
The head unit on the Reese M5 20k Fifth Wheel Hitch, part # RP30928, can be removed from the head support of the hitch by removing one large pivot pin held in place by a large cotter pin. This will make it easier for one person to remove the hitch from the vehicle. Our description says two pins and clips, but it is only one on the 20K hitch. I am going to have them update that information.
The rubber bumpers included with the # RP30928 hitch are designed to prevent and/or limit contact... view full answer...
Yes, the mounting hardware comes with Curt trailer hitch # C11204. I have linked the installation instructions for you.
For towing you can use the # 3593 ballmount, then either a 1-7/8 inch ball # 19256 or 2 inch ball # 19258. For trailer wiring use # C56175 .And finally a pin and clip # F-4. I have linked instructions for the wiring as well. view full answer...
The Curt 2-inch Class III trailer hitch # 13328 that you referenced is a valid fit for your 2005 Honda Pilot and is the one of the three options for your car that I recommend because it has the same capacities as the others but costs less. All required hardware is included for bolt-on installation (no drilling!) and an install video is linked for you to show you the entire process. This hitch is custom-designed just for your Pilot.
You will also need a ball mount, hitch ball (of the size... view full answer...
Curt trailer hitch # C12170 fits the entire model year 2016 Mazda CX-5.
If you plan on doing any towing the recommended ball mount is # C45521and a hitch pin and clipF-4. For a 1-7/8 inch ball use # 19257 and for a 2 inch ball use # 19258.
For trailer wiring you can use wiring harness # 118563 to add a 4-Way flat connector to the rear of the vehicle. view full answer...
Yes, so long as your fully loaded trailer is rated below the capacities of the hitch for your Volvo (and also the capacities of your 2012 Volvo C30), the hitch is perfectly safe. The hitch, as well as the rest of the parts you need for towing are the following:
- Curt Trailer Hitch Receiver # C11337
- Wiring Harness # C59496
- Curt Drawbar # C45521
- Pin and Clip # F-4
- 2" Hitch Ball # C40018 or 1-7/8" Hitch Ball # C40001 view full answer...
Draw-Tite trailer hitch # 36540 does fit the 2013 Toyota Avalon Hybrid model. Before buying a hitch, though, please consult the owners manual and/or Toyota to make sure it is permissible to install the hitch, especially if you plan on doing some towing. I have included a link to the installation instructions for you.
If towing is an option then for a ball mount use # 36071 and pin and clip # PC2. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use... view full answer...
As the hitch pin on your Hollywood Racks Sport Rider # HR1000Z bike rack is threaded, the Master Lock # 2866DAT locks will not fit without having to drill the threads out of the shank. The threads are there so that when you tighten the pin into the shank, it will secure the rack more tightly and keep it from wobbling in the hitch. Drilling them out will cause you to lose this feature.
I can also say that Master Lock parts will only work with Master Lock parts, so there is a very very high... view full answer...
The Curt Hitch # C11111 will not require drilling for installation on your 2012 Infiniti M37, however there will be some trimming of the underbody panel prior to installation. This trimming would not be visible from the rear of your vehicle. This trimming is necessary to allow the receiver opening to pass through this panel. Check out the installation instructions that I attached that show how it will be modified.
This hitch comes with a ball mount and a pin and clip. You may also be interested... view full answer...
What I would recommend you do is find the biggest cooler that will fit in the available space in front of your radiator and install it along with the factory cooler of your 2006 Nissan Frontier. This way you will maximize the cooling of your transmission fluid. The Derale Cooler part # D13501 is 11" Wide x 5-3/4" tall x 7/8" deep.
I attached an FAQ article on transmission coolers as well as an install video for you to check out also.
For a hitch I would recommend the Draw-Tite part #... view full answer...
Locks are not included with the Reese Cargo Carrier # 63153 that you referenced but I can absolutely recommend a lock that will work perfectly. To secure the carrier to your vehicle I highly recommend the etrailer.com Trailer Hitch Receiver Lock # e98880. This will take the place of the standard pin and clip to attach the cargo carrier to the hitch receiver. It features a patented, pick-proof, screw-and-lock security design, a double-chrome plating for superior rust resistance, and all... view full answer...
The most popular hitch receiver for your 2007 Jeep Grand Cherokee Laredo is the 2-inch Class III hitch # 13251 from Curt. This installs without drilling, as do all other available hitches that you can see on the linked page. This hitch fits all GC models expect the SRT-8.
This 2-inch Cass III hitch gives you a higher capacity than smaller 1-1/4-inch types but also costs less than other Class III hitches. All required mounting hardware is included and an installation video is linked as... view full answer...
Draw-Tite Class III hitch # 75278 is a confirmed fit on the 2008 Chevy Uplander with 113-inch wheelbase. I verified this with Draw-Tite. This particular hitch fits all styles of this vehicle year/make/model.
An installation video for this item is linked for you along with a helpful article.
For a 4-pole wiring harness to power trailer lights (or a lighted hitch cover like # RP86530) you can use plug-and-play harness kit # 118396. For a towing kit with ball mount and hitch balls use part... view full answer...
I can certainly make some recommendations for a towing set up on your 2007 Toyota Sienna. Starting with a trailer hitch, the most popular hitch for your vehicle is Draw-Tite # 75237. This is a Class III hitch rated for 4,000 pounds gross trailer weight, 400 pounds tongue weight. The trailer you plan to tow is right at this limited. If there is any way you can reduce the weight of the trailer some, it would be more ideal.
I have included a link to the installation details and a video showing... view full answer...
I can help you out with hitch for your 2014 Acura MDX, the Curt Trailer Hitch Receiver # C13146 is a great choice.
The Curt is going to offer your '14 MDX great bumper and ground clearance; when we test fit this hitch on a 2014 Acura MDX we found it was about 2-3/4 inches from the hitch pin hole to the edge of the bumper, and 14 inches from the top of the hitch to the ground. That will give you really nice clearances to keep your bikes away from the back of your Acura as well as help... view full answer...
The trailer hitches we offer that are designed to fit your 2005 Grand Caravan do not come with a wiring harness or ball mount kit but I can help you out with that.
First, I recommend installing a Class lll trailer hitch like part # 75305 with a 2-inch receiver opening. It is a more heavy-duty hitch and it offers many more options for accessories.
For the Class lll hitch I recommend the etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop... view full answer...
Go To Results