Flat towing a vehicle is always subject to the okay of the auto maker and the best place to check this is in the owner's manual (or with your local dealership which can see the car's specific factory-installed equipment by looking up its VIN). Page 4-26 of the online edition of the owner's manual indicates that one version of the car cannot be flat towed, that version being the 3.9L V6 engine with the four-speed automatic transmission. Since you have the 3.5L you can flat tow the car but... view full answer...
Since kayaks vary considerably in size and weight I suggest that to start you check your G6 owners manual or consult with your local dealership to verify the roof weight-bearing capability for your vehicle. It is quite possible that a given kayak, plus the weight of the kayak carrier and the roof rack you choose, could exceed a vehicles roof weight capacity. Once you have confirmed the G6 has the capacity you need for transporting your kayak then you can choose a rack and carrier.
The... view full answer...
We have a trunk-mounted bike rack for the 2007 Pontiac G6 Coupe with a spoiler.
It's the Hollywood Racks Expedition 2 Bike Carrier, part # HRF6-2. This works with most factory spoilers and has anti-sway cradles. The arms are adjustable and reduce the need for an adapter bar. It can support up to 2 bikes up to 35 pounds each.
I've linked to a video review of this rack below. view full answer...
Per the 2008 Pontiac G6 owner manual the maximum weight of a trailer used should not exceed 1,000 pounds. So as long as the cargo trailer you use is less than 1,000 pounds when fully loaded, you can tow it using your G6 with the Draw-Tite Trailer Hitch Receiver # 36426. Even though the hitch is rated higher, you're always limited by your lowest rated component, which in this case is the vehicle. view full answer...
For your 2009 Pontiac G6 the correct base plate kit is the part # 3165-1 and not the # 3136-1 that you referenced as that base plate is for Saturn Ions.
The final authority on what needs to be done to flat tow your vehicle is the owners manual. Without knowing more info on your vehicle the best I could find for your vehicle is that if it has an automatic or manual it is flat-towable as-is as long as you keep it under 65 mph. You need to verify this though with your owners manual.
In addition... view full answer...
You can use the Demco base plates # DM9517188 for your 2009 Pontiac G6 GT. But first, you are going to want to consult the vehicle owners manual to determine if the vehicle can be flat towed and if there are any special requirements. From what I found if the vehicle has the 3.9 liter V6 motor it cannot be flat towed. But it is not clear if it can be dolly towed or not. You would need to talk to a GM tech at a dealership to determine if dolly towing is acceptable.
If you find that you can... view full answer...
The Draw-Tite Trailer Hitch, part # 36426 you referenced, is a fit for your 2009 Pontiac G6, if it is not a convertible. This is a class ll hitch with a 1-1/4 inch receiver opening.
The maximum towing capacity is 3500 lbs, and the maximum tongue weight is 300 lbs. I would recommend you check your owners manual or with your local dealership concerning the towing capacity of your vehicle if you are planning on towing. If so, you will need a ball mount. I would recommend Class II ball mount... view full answer...
According to Roadmaster, the Roadmaster XL Base Plate Kit, # 3132-1, that you have referenced is the correct kit for the earlier model 2009 Pontiac G6 models before the updated fascia. This base plate kit fits all models except the GXP and convertible, so this is the right kit for you.
There are several other items that you will need to flat tow your G6. I have incldued a link to an article on the 5 basic components needed to flat tow a vehicle. I have also incldued a link to our series... view full answer...
You will need to use a circuit tester, like # PTW2993, in order to determine the functions of the taillight wires on the 2009 Pontiac G6 if you are hardwiring a 4-Way connector to the vehicle. This involves turning on the blinkers, brake lights, and running lights in succession and then probing each wire to match the right function with the right wire. I have included a trailer wiring FAQ article that goes into more depth of wire and function below.
I recommend installing the Curt Custom... view full answer...
To be on the safe side we recommend using the license plate bracket of the Thule Transporter Combi Hitch Mounted Enclosed Cargo Carrier # TH665C so that the plate is always displayed well. Most likely it would take a pretty bored police officer to pull you over for this carrier blocking the plate's view, but checking with your local DMV/DOT would be best call on that. view full answer...
The Curt # C12333 trailer hitch that fits your 2007 Pontiac G6 actually comes with bolts and a fish wire tool so you do not need to order those separately.
If you just need replacement hardware that is available at part # RHK; on the product page you only need to put in the hitch part number and select Curt in the Manufacturer drop down. view full answer...
For your 2005 Pontiac G6 you could use a trunk mounted bike carrier. The Hollywood Racks Express 3 # HRE3 is a versatile carrier that fits the sedan and coupe models, but it does not work with spoilers. Looking at the pictures of this rack installed and pictures of the Pontiac G6, I believe it would avoid the small flat spoiler on the G6. I have included a link to a video review for you to check out and see what you think. .
You can also install a trailer hitch, # 36426, and use a hitch... view full answer...
According to Rhino Rack's fit information, the Rhino Rack Vortex Roof Rack consisting of the # RRVA126B-2 crossbar, # RRRLKVA legs, and the # DK067 Clamp Kit is indeed compatible with your 2006 Pontiac G6.
The Thule # TH82WV fairing would be compatible, as Thule and Rhino Rack square crossbars share the same 1-1/4 inch width and 3/4 inch height. The Thule # TH7324 snowboard carrier you mentioned would indeed be compatible with the roof rack.. view full answer...
If you have a motorhome mounted tow bar like the Roadmaster Nighthawk All Terrain Tow Bar part # RM-677 then you should not have any issues at all using the Curt Clamp-On 3 Bike Rack part # C18013. I called my contact at Roadmaster to confirm this as well.
Please note that if any of your bikes have an alternative frame or deep drop tube then you are almost certainly going to need to use the Thule Bike Frame Adapter Bar part # TH982XT to keep the bikes for interfering with the tow bar.... view full answer...
I would recommend the Draw-Tite Class II, part # 36426. When we installed it on a 2008 G6, we found that the distance from the receiver hitch pin hole to the furthest rearward point of the rear bumper was about 6 inches.
The Swagman XTC2 you mentioned, part # S64670 has a distance of 8 inches from the hitch pin hole in the shank to the edge of the closest wheel hoop. Since the shank is angled to provide a 3 inch rise, the pedals of your bike should be well above the rear bumper so the... view full answer...
I went out to the warehouse to inspect the Camco RV and Marine Septic Safe Toilet Tissue, # CAM40276, and the 2-ply version # CAM40274. I also spoke to a co-worker who has used these items and got her opinions.
The single ply is soft but thin like any single ply toilet tissue. When bunched up it is fairly strong and I would not anticipate breakage problems. My co-worker confirmed this saying they have never had a problem with it breaking. Since the material is thin and designed to dissolve... view full answer...
To install Bearing Buddies, you first need to know the grease cap diameter needed by measuring the inside of your trailer hub diameter at that location. I recommend using a digital caliper like # PTW80157 for a precise measurement.
I've attached an installation video to assist. This Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair) # BB1980A-SS are a confirmed fit for 1.980 inch hub bore. view full answer...
I have good news and bad news for you. The good news is that I can offer you a roof rack solution. The bad news is that Thule no longer offers a rack fit for your vehicle.
I checked with Thule, and found that Thule used to offer a 2161 fit kit for the G6, but it was compatible with their 400XT roof rack foot which has been discontinued. When Thule discontinued the 400XT foot, they stopped making the 2161 fit kit as well.
One of the most economical solutions I can offer is a Rhino Rack... view full answer...
The Draw-Tite hitch, part # 36426, will fit your 2008 G6 GXP as long as the body parts are factory parts and not dealer or aftermarket. According to the instructions, you will not have to cut or trim the rear fascia. I have added a link to the instructions below for you to review. view full answer...
Yes, it is possible to put hydraulic disc brakes on a tow dolly. We do not offer a kit specifically to add disc brakes on your dolly, but I am happy to walk you through all the parts you will need.
However, there are a couple of things we need to know to choose a disc brake kit for the dolly.You need to know what the weight capacity of the your axle is to make sure you get the correct brake assemblies. If you do not know the capacity, there should be a label or sticker on the axle that... view full answer...
Go To Results