At this time we do not offer The installation hardware kit for the Aries 3068 Brush guard. We do offer The Aries Grille Guard - 1 Piece - Semi-Gloss Black Powder Coated Steel # AA3068. This is the whole kit. Which has a simple bolt-on installation. view full answer...
When it comes to the proper towing mirrors for your 2013 Ford Explorer I recommend The K-Source Universal Towing Mirrors - Clip On - Convex Mirror - Qty 2 # KS3891-2. These extra-large universal towing mirrors clip over your existing side mirrors to give you an extended rear view. They have a snug fit that reduces mirror vibration. The mirror dimensions per mirror are 7-3/4 inch tall by 5-1/8 inch wide.
I have attached an installation video link below. view full answer...
I do have a simple option for you to convert the 4-way trailer connector you have now to a 7-way trailer connector but it will not be entirely plug and play as that is not an option. The only thing you will need for this is the Adapter 4-Pole to 7-Pole and 4-Pole part # 37185 unless the trailer has brakes in which case you will need the Universal Installation Kit for Trailer Brake Controller part # ETBC7.
The above two kits both will install in the same way. The two 4-ways plug into one... view full answer...
We do have a great solution but we do not have custom fit towing mirrors for your 2002 Ford Explorer XLT.
The universal fit towing mirrors I recommend for your Explorer are the K-Source Unviersal Dual Lens Towing Mirrors - Clip On # KS3990. These universal fit mirrors fit most mirrors 4-1/2 inches to 11-1/2 inches tall. Clips on the mirror arms grab the edge of your factory mirror housing in the space between the mirror and the housing. The snug fit helps reduce mirror vibration and the... view full answer...
I wasn't able to find your order number so I'm not sure what harness you purchased from us specifically for your 2015 Ford Explorer, but if it was the T-One Vehicle Wiring Harness # 118540, and you didn't have the two connectors, you would only need to plug it in to the connector shown in the accompanying photo I added. This is from the linked video install of this harness on a 2015 Explorer. If you did this and the connectors matched up but you still don't have power there are a number... view full answer...
Yes the Malone roof rack part # MPG217 is a confirmed fit for your 2013 Ford Explorer and also is compatible with your Thule The Stacker part # TH830. view full answer...
The Thule Transporter Combi Hitch Mounted Enclosed Cargo Carrier TH665C (discontinued) comes with an anti-rattle hitch bolt but if you want to upgrade that to a locking hitch pin you just need the Thule Snug Tite Hitch Lock # THSTL2 which is compatible with both 1-1/4" and 2" hitch receivers so this is perfect for your application.
Attached is a review video for you to check out. view full answer...
Yes, you will be able to use the Thule DoubleTrack Pro XT Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount, part # TH92BJ, with your men's Electra Townie 7D bikes.
I have included a video review of the DoubleTrack below. view full answer...
There is not hardware included with the Westin Replacement End Caps # 80-0221 or # 80-0220 so you will need to source that hardware locally. You will want to use a #8-18x.50" Phillips head screw, which you should be able to obtain from any local hardware store. view full answer...
The instructions and product description are stating that the round tube style receiver hitches from Draw-Tite and Hidden Hitch will not fit on Explorers made in 1998 and later with a full size, 16 inch spare tire.
You can install the Draw-Tite Class III Max Frame Receiver Hitch, item # 75096, with the full size spare. You may have to lower the spare to install these hitches, but it will be repositioned after the install is complete.
If you do not have the 16 inch full size spare then... view full answer...
You had it right, the 40 amp Inline Circuit Breaker, part # 9150 is what you need. We recommend using at least a 12 gauge wire for this circuit. You can certainly use 10 gauge if you wish. view full answer...
Since your 2004 Explorer was not equipped with a factory 7-way, the brake controller will need to be hardwired.
To wire your controller, you will need:
25 feet of # 10-2-1 duplex cable
Either a 20- or 30-amp inline breaker (# 9506-P for 2-4 brake assemblies or 38630 for 6 brake assemblies)
40-amp breaker, # 9510 for 12-volt accessory circuit (if needed).
Circuit Tester, # PTW2993
The controller would attach to the underside of the dash and should be mounted in accordance with the guidelines... view full answer...
With just the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118540 installed not connected to a trailer there would not way it would just put an amperage draw on the electrical system. Current has to go somewhere to draw from the battery so it just being installed without powering lights it can't drain the battery. view full answer...
The WeatherTech Cargo Liner # WT401304 measures about 44" from behind the seats to the rear hatch area and is designed to sit behind the 2nd row seating. If you are wanting to keep your 3rd row seating up and available for use (if you have it) then you'll want the WeatherTech Cargo Liner # WT401305 instead.
The 401304 that you referenced is the largest custom liner available as there isn't anything made to reach from right behind the driver's seat all the way back to the hatch. You can... view full answer...
The Tekonsha T-One Vehicle Wiring Harness # 118599 will give you a 4-way flat connector for your utility trailer to connect to your 2022 Ford Explorer. This harness uses factory style connectors so you will not have to splice into the tail light wiring on your Explorer.
The Mounting Bracket # 18144 will allow you to secure the 4-way connector on the back of your Explorer to prevent it from becoming damaged if you choose to route the connector outside the vehicle rather than running it... view full answer...
As long as you have a set of round, square, aero, elliptical, or factory crossbars, the Yakima SkyBox 18 Rooftop Cargo Box # Y07336 will fit your Explorer.
If you don't you'll need to add a set of crossbars. If you have flush mounted rails, you can use the Inno Square Crossbars # INB117, with the Inno Feet for Square Crossbars # INTR, and the Custom Fit Kit # INTR103.
if you have factory rails that run front to back, then you can use the Thule WingBar Evo Crossbars # TH711220 with the... view full answer...
Based on your description I'm sure you have the Hollywood Racks Road Runner Bike Rack # HR520. Your bike rack fits a 2" hitch. I recommend the etrailer Trailer Hitch Receiver # e29YR. This has a 2" receiver and a bolt on installation. It also has a maximum tongue weight capacity of 600 lbs to handle your bikes and bike rack. The etrailer hitch features a matte black powder coat finish for a rugged look and comes with a limited lifetime warranty. view full answer...
Congrats on the new vehicle! Yes, we do have a set of crossbars that will attach to the raised side rails on your 2023 Ford Explorer. You will want the roof rack by Rhino-Rack and it includes the following parts:
Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 59" Long - Qty 2 item # RRVA150B-2
Rhino-Rack SX Series Legs for Vortex Aero Crossbars - Raised Factory Side Rails - Qty 4 item # RRSX100
This aero bar roof rack system has plenty of capacity for a cargo box. The crossbars... view full answer...
The Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers # 3035-P is the correct wiring adapter harness for your 2022 Ford Explorer with factory 7-way to use the Tekonsha Prodigy P3 Trailer Brake Controller # 90195. view full answer...
Yes, the Rhino-Rack 2 Kayak Carrier w/ Tie-Downs part # S512-S512X will work perfectly with any of the Thule WingBar Evo Crossbars like part # TH711420 for example. For future reference, the Rhino-Rack 2 Kayak Carrier will work with crossbars from most aftermarket companies such as Yakima, Thule, Rhino Rack, Malone, Inno, Rola, and more. Therefore, the carrier can be easily transferred to another vehicle down the road no matter which roof rack it has.
The Rhino-Rack 2 Kayak Carrier comes... view full answer...
Go To Results