With pintle hitch trailers typically being a very high weight they do not offer one for a 1-1/4" receiver due to the light duty capacity of the small receiver. I do see you input your vehicle as a 2016 Ford Explorer which we do offer a 2" Receiver # e98867 for. This would allow you to use a B&W Tow & Stow Pintle Hook with 2" Ball # BWTS10055. The Curt Hitch # C45910-15-20 you found has a 2-5/16" ball. view full answer...
You can use the Yakima TopGrip Paddle, Shovel, or Axe Holder Brackets for Roof Rack Crossbars - Universal Mount # Y04086 to attach your paddles to the crossbars on your Malone MicroSport Trailer with J-Style Carriers for 4 Kayaks - 800 lbs # MPG462G2. This would allow you keep the paddles out of your vehicle and safely attached to the trailer.
I've linked a review video of this bracket for you to check out. view full answer...
We do not have a 20" wide quick attach model of step similar to the TorkLift GlowStep Camper Scissor Steps # TLA7802.
The closest we have to 20" wide that are detachable are the Brophy Camper Scissor Steps # SS02 which are 17" wide. view full answer...
I have a solution for you, but the Thule Rapid Traverse Feet # TH480R are not designed to fit on flush mounted roof rails, so there's not a fit kit that will allow this; additionally, your older square bars will not fit in the feet that are available for your 2016 Ford Explorer. For these reasons, if you wanted an aftermarket roof rack for your 2016 Ford Explorer so that you've got flat bars, you would need to get an entirely new system.
If you wanted to go the aftermarket route, I recommend... view full answer...
That would depend on a few things like the handlebar length of the inner most loaded bike on the Hollywood Racks # HR1400Z as well as the height of the bike and the hitch you have installed. There is a rack I can guarantee will give you full access to rear cargo area of your vehicle with bikes loaded with the Thule Apex Swing # TH9027XT which swings out and away from the rear of the vehicle to give complete access without any guesswork.
Check out the review video link I attached for more... view full answer...
We do offer no-drill rear mud flaps for your 2009 Ford Explorer Sport Trac. Rock Tamers offers their heavy-duty hitch-mount Adjustable Mud Flap System # ERT00108 that fits on a 2-inch hitch ball mount. These are easy to install and remove and they adjust both vertically and horizontally. They can even be trimmed to a specific size if you like. Please refer to the linked video. A similar system is offered by Roadmaster, their kit # RM-4400-73.
If you do not have a hitch then you can use... view full answer...
In order to put crossbars on the flush mounted side rails of your 2019 Ford Explorer you'll want to use the Rhino Rack # RRRCH4 feet with # RRRCP45-BK fit kit and the Rhino Rack Vortex Aero Crossbars # RRVA137B-2. Rhino Rack offers a similar quality and durability of the more expensive roof racks at a much better price point and they will allow you to carry a kayak carrier Thule Hull-A-Port # TH834. This Rhino Rack will mount to the fixed mounting points on your flush mounted side rails... view full answer...
Yes, you can get the Thule roof rack in silver for your 2017 Ford Explorer. The only parts you need for the install are the Thule WingBar Evo Crossbars # TH711400, Rapid Podium Feet # TH460R, and Fit Kit # THKIT3151. view full answer...
When it comes to the spring bars for the Pro Series Weight Distribution with Friction Sway Control, # PS49583, you can replace your current spring bars with the Pro Series Replacement Round Bars, # PS58439, which would offer you the 550 lb tongue weight capacity. view full answer...
Yes, there are rooftop bike carriers available that do not require you to remove the front wheel.
The Rhino-Rack MountainTrail Rooftop Bike Carrier # RBC035 is a fork mount style bike rack, which does require you to remove the wheel.
What you are wanting is a wheel mount style like the Yakima FrontLoader Wheel Mount Bike Carrier # Y02103. This rack will not require you to remove your wheel and works with wheels from 20" - 29". view full answer...
Yes, the OptiMate Solar Duo Solar Charging System with Controller # MA49JR is safe to you on your Lithium batteries and can also be used with lead acid batteries. The multistage smart charger helps to extend battery life by not overcharging your batteries. It can be used on batteries from 2 amp hours up to 240 amp hours. view full answer...
The Ford Interceptor is based on the Ford Explorer so it is very likely that the Curt wiring harness part # C56172 would fit it.
What you can do is check out the install video I attached that shows this harness being installed on a similar 2015 Explorer and then check your vehicle once it arrives to see if the install connectors are there. view full answer...
You're correct that the three hitches we offer for your 2003 Ford Explorer (shown on the linked page) are intended to install along with, but not to replace, your factory-installed hitch. This is because the OEM hitch is actually part of the vehicle's rear bumper structure and cannot be removed. An aftermarket hitch like the Curt # C13550 will therefore install just under the OEM hitch but remain independent of it. This resulting 2-hitch configuration means you could potentially use the... view full answer...
All of the trailer hitches we carry for the 2013 Ford Explorer will have the receiver and part of the crosstube visible beneath the rear fascia on the vehicle as you can see in the video I have linked showing installation of Curt hitch # C13386.
If you plan on doing some towing with the hitch I also recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a storage bag. And for trailer wiring you can use # C56093. view full answer...
We do have a universal towing mirror option that would work great on your Explorer. The K-Source Clip On Towing Mirror, part # KS3891 would work great for you. The mirror clips to your factory mirror, using two ratcheting rubber straps. The straps make for an extremely secure, almost vibration free-fit. As you can see by looking over the reviews, the # KS3891 is very highly rated by our customers.
Unfortunately, none of our mirror vendors manufacturer a custom slip-on mirror that would... view full answer...
All three of the 2-inch Class III hitches we offer for your 2004 Ford Explorer can be seen on the linked page and all three are as you noted intended for use along with the OEM 1-1/4-inch Class II hitch that came on the vehicle from the factory. We do not offer any Class III or Class IV hitches that actually replace the factory hitch.
The highest rated hitch option is the Draw-Tite # 75132, which is rated for 500-lbs tongue weight (TW) and 5000-lbs gross trailer weight (GTW). If you use... view full answer...
If you are referring to the draw bars (also called arms) for a set of flat towing base plates that are installed on your 2003 Ford Explorer we do offer these. If you are referring to factory tow hooks these we do not offer and you will need to obtain them from Ford.
The replacement draw bars/arms for base plates will be specific to the brand and model of base plate. All such base plates we offer for the vehicle are shown on the linked page.
If you mean a front-mounted hitch we do have... view full answer...
The only trailer hitch cover that features a flag and is directly compatible with an 1-1/4 inch hitch receiver is our American Flag Trailer Hitch Cover, part # AUT2-FLAG-C. This premium hitch cover has a polished stainless steel base so you won't have to worry about rust or corrosion.
To secure the hitch cover to your hitch, I recommend using a pin and clip # C21410 or a hitch lock like # e98879 which will deter theft. view full answer...