The dimensions of the rectangular metal nut part on the Yakima HD Bar SL Adapter 4-piece kit # Y03541 (their part 8003541) and the single piece part # 8880637 are shown in the linked image. The metal nut measures 1-1/8-inch x 3/4-inch. The overall height of the nut from the top to the wider base part is 3/4-inch. view full answer...
The four bolt pattern of the flange on the waste water valves is an industry standard so you don't really have to worry about measuring the bolt hole spacing. However, to address your specific question the bolt holes are spaced 3.73" apart but depending on how exact you were measuring, you could get anywhere from 2-5/8" to 2-3/4" as its hard to get the exact center of each hole. Therefore, the Bristol Waste Valve Body for RV Black Water part # 34439240 will work for you just fine. The only... view full answer...
I've pulled the Draw-Tite Front Mount Trailer Hitch Receiver # 65063 and here are your measurements.
1: 29-1/4"
2: 3-1/2"
3: 32"
4: 5"
5: 2-1/4"
I've included a video to help you with the install, so check that out! view full answer...
In most cases it's a bit safer to go on the slightly lower nose height setting instead of slightly higher since higher can sometimes cause sway. But if the vehicle is going to squat quite a bit from the weight of the trailer then the higher would work better which would be the case with the 4 inch drop ball mount part # 2753. view full answer...
According to what I can see in the online user guide, your 2010 Ram 1500 5.7 Quad Cab 4x4 should have a 10,450 lb max towing weight and a 1,510 lb max payload. That being said there is a lot of variance between these different Ram models, and we do suggest consulting your owners manual to confirm the towing capacities of your specific vehicle. This information can also be found on the stocker in your door.
If you are in the market for a new fifth wheel hitch, I recommend the B and W 16K... view full answer...
The Husky Center Line Weight Distribution Sytem # HT32217 comes with a shank that has an overall length of 12 inches. I've attached a diagram with some other important measurements for you. Measurements at the top are when used with the trunnion system. Measurements at the bottom (A-F) are the overall measurements. view full answer...
I spoke to my contact at Westin and he told me that the best way for you to figure out how far out the Westin Sure-Grip Running Boards # 27-6650-1905 will stick beyond the sides of your vehicle would be to measure inches out from the very bottom of your rocker panels.
These running boards are 6 inches wide and install at the bottom of your rocker panel, so measuring out 6 inches from the rocker panel will tell you exactly where they will be. view full answer...
I checked with the manufacturer, and verified the weight is 138 lbs of the BedSlide Sliding Truck Bed Tray w/ T-Tracks - 5" Rails - 1,000 lbs # BE39ER. view full answer...
I do not have any information regarding the capacity of the OEM tow hooks. The 9000 lb line pull refers to the fact that the receiver is capable of pulling 9000 lbs in a straight line from the receiver opening (not at an angle from side to side or up and down). In order to install the receiver, the OEM tow hooks would need to be removed.
I do not have a photo of the receiver installed on a vehicle, as we have not yet had the opportunity to install one, but if you look at the installation... view full answer...
The Kenda Karrier ST225/75R15 Radial Trailer Tire # AM10303 weighs approximately 24-lbs. All tires and wheel/tire items in this size are displayed on the linked page. The weight of each one appears above the yellow Add to Cart button. view full answer...
The specs I found for the 2018 Dutchmen Coleman Lantern 263BH tandem axle travel trailer indicate a dry weight of 5871-lbs and a payload capacity of 1729-lbs. Added together these become the GVWR for the trailer, the gross vehicle weight rating, the most it can weigh when fully loaded and ready for the road. In this case that GVWR is 7600-lbs.
The rule of thumb is that a trailer must have tongue weight (TW) of 10 to 15-percent of the trailer's gross weight. I would suggest to try to stay... view full answer...
The correct Blue Ox baseplate for a 2013 Ram Tradesman is item # BX2409. It is designed for the Ram 1500 trucks with a plastic molded bumper. The item # BX2409 is for the Ram's with a chrome metal bumper. I wanted to mention you can not flat-tow a 2WD 2013 Dodge 1500 no matter what trim you have. If you have 4WD you are good to go.
Some other parts you will need to flat tow your 2013 Ram Tradesman are listed below:
Tow Bar and Safety Chains - Blue Ox Alpha 2 Non-Binding Tow Bar item #... view full answer...
Trailer weight distribution/sway control systems (WD/SC) are best selected after measuring the actual tongue weight (TW) of your trailer when it is loaded up with your usual mix of supplies and recreational equipment, and with your water and propane tanks filled, etc. Dry hitch weight by itself is not ideal for deciding on a system because it will always be lower than your loaded TW. Tongue weight scale # e99044 takes the guesswork out of the equation. To this you need to add the weight... view full answer...
The problem is that the overall measurement at 27-5/8 inches is from the end of the rod that extends out on both sides. The 26-1/8 inches is the dimension of the mounting brackets at the top of the steps.
I have attached a photo with dimension noted of the Flexco Manual Pull-Out Steps # SMFP-2100 you can check out. view full answer...
The mounting holes for the ball mount on the Channel Style Adjustable Ball Mount # C45900 are 1" apart on center. I have attached a photo demonstrating this and some other measurements for you as well. view full answer...
For some vehicles the throttle body spacers do not provide much of an increase, but for the 5.7 liter Hemi engines in the new Dodge vehicles every review I have found listed a noticeable increase in power and fuel mileage gains between .5 and 2 miles per gallon.
The mileage will depend largely on driving habits but horsepower and torque would realistically be around 5 more for both. view full answer...
I would recommend using the exact procedure you outlined. Tighten the shank bolts first and then with the shank in the vehicle hitch (secured with hitch pin) torque down the hitch ball to 450 ft lbs. view full answer...
If you check out the attached picture you'll see a wiring diagram for the Superwinch Solenoid part # SW87-42608 that you referenced. view full answer...
The clearance in your 2016 Ram 1500's wheel wells really limits your options. The best chains for 275/60 R20 tires are going to be the Glacier Cable Tire Chains item # PW3029C. These are class S chains that will give you good traction in both light snow and ice. The low profile construction will provide a smooth ride and you can add the rubber adjusters item # PW97 to ensure the cables remain properly seated on the tires.
I have linked an installation video below to help you get these... view full answer...