Weight of BedSlide Sliding Truck Bed Tray With T-Tracks - 5" Rails BE39ER

Question

Question:

What is the weight of the rail system

asked by: Guy

1

Helpful Expert Reply:

I checked with the manufacturer, and verified the weight is 138 lbs of the BedSlide Sliding Truck Bed Tray w/ T-Tracks - 5" Rails - 1,000 lbs # BE39ER.

expert reply by: Kyle S

1

Answer 1

SumoSprings would definitely be the solution I would recommend for your squatting concern. The SumoSprings Solo Custom Helper Springs - Rear Axle item #SS45MR have a 2,800 lbs capacity which would eliminate that carolina lift look you get when your…

view full answer...

Answer 2

The Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F95FV will be just fine if you need to lift your 2022 Ford F-250 Super Duty, but it will be good practice to lower the psi rating to 5 prior to lifting the truck. I confirmed this…

view full answer...

Answer 3

The Truck Trolley Sliding Truck Bed Tray #TR87VR actually just installs using straps, which is why it has a 300 lb weight rating as opposed to 1,000 + lbs like we see with some of the sliding cargo trays that bolt to the truck bed. The installation…

view full answer...

Answer 4

If a 1000 lb round bale is the heaviest thing you'll haul in the truck bed, I'd recommend going with the SumoSprings #SS95MR that you'd looked at, which would provide you a little bit of leeway in case the bales vary in weight a bit as…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Weight of BedSlide Sliding Truck Bed Tray With T-Tracks - 5" Rails BE39ER

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching