For a single bar Rhino Rack roof on the 2019 Nissan Frontier King Cab S, you need part # RRVA137B for the bar, part # RRRLKVAH for the feet, and part # DK374H for the fit kit. The JA4079 you mentioned is Rhino Racks part number for the whole kit but the part numbers I just mentioned are etrailer.com individual part numbers for the same setup. view full answer...
If you will be using the Curt Echo Mobile Trailer Brake Controller part # C51180 then the 7-Way RV Upgrade Kit for Trailer Brake Controller Installation part # ETBC7 is exactly what you need. In regards to installing this, all you will need to do is run the black wire that comes with the kit from the black wire on the back of the 7-way up to the vehicle's battery with the 30 amp circuit breaker in between and then ground the white wire from the back of the 7-way to a bare metal surface... view full answer...
The Flash E Series Adjustable part # FA42-00-2800 will work well for your 2008 Nissan Frontier hitch that is 17.5" from the top of the receiver to the ground and the trailer that has a coupler 24 inches from the ground when level. You do need about 6.5" of rise to be level, you can pin the ball in the second to last hole from the top. view full answer...
There are a few different ways that the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267 can be installed which will vary based on if the motorhome has a separate or combined lighting system and if the vehicle has a separate or combined lighting system. The 2017 Nissan Frontier has a separate lighting system therefore, I have attached two diagrams for you. There is a diagram if your motorhome has a separate lighting system and there is a diagram if your motorhome... view full answer...
It is possible to flat tow a 2013 Nissan Frontier 4x4 with an automatic transmission but you'll need to have a driveshaft disconnect installed on the truck. We do not carry these but we do have everything else you'd need. If you need help finding a source for a driveshaft disconnect let me know as I can help point you in the right direction.
First thing you'll need is a base plate kit like the # 344-1B which was custom made to fit your Frontier.
In addition to the base plates, you will... view full answer...
Long story short, that's not going to work for you even with a double line pull using a snatch block like the # CU881079. In reality, you need at least 1.5x the GVWR of your vehicle when it comes to winch capacity. The # BDW10044 I mentioned as a better choice would be the bare minimum you'd be able to get away with and still be able to recover your 2019 Nissan Frontier from a situation that required a winch. The 6000-lb capacity ComeUp # CU854768 is not going to work with your 4700-lb... view full answer...
The Erickson Over-The-Cab Truck Bed Ladder Rack # EM07707 measures 135" long x 54-13/16" wide x 32-7/8" tall so it is going to hang over your windshield slightly to allow you to carry longer loads without damaging the cab; it will stick out a very small amount from the back because of the handles on the back of the rack, but the amount is negligible. The height of this rack is not adjustable so it won't have the ability to raise and lower the bars as needed in a similar manner to the Yakima... view full answer...
I have a solution for you, but the Thule TracRac TracOne # TH27000XTB is not compatible with the Nissan Utili-track system. For a Thule Ladder Rack system that is compatible with your 2018 Nissan Frontier's Utili-track system you would want to instead use the Thule TracRac SR # TH43001XT-600 (for 6ft bed) or # TH43001XT-603 (5ft bed) which offers a more functional sliding ladder rack for your 2018 Nissan Frontier.
If you're looking for something a little bit more budget friendly, the Erickson... view full answer...
The SuperSprings Custom Suspension Stabilizer # SSA1MTKT are not intended to increase the height of your 2007 Nissan Frontier. The stabilizer is meant to provide more support for your vehicle when carrying heavy loads in the cargo area or towing a trailer as well as protect your existing suspension and your brakes and tires.
This product will maintain the stock height of your vehicle and the only way it should raise the height is if your vehicle is already sagging due to poor support due... view full answer...
On a transmission cooler like # D12902 or any for a 2007 Nissan Frontier, the new cooler is a supplemental unit. The fluid will flow from the transmission, to the factory cooler in the radiator, out of the radiator, into the new cooler, then back to the transmission. In some cases you can use a cooler to bypass the factory cooler but you would have to block off the factory inlet/outlet cooler ports on the radiator. Also a larger and more efficient cooler should be used. I have included... view full answer...
The trailer wiring harness that you will want for your 2010 Nissan Frontier is the Tow Ready T-One Vehicle Wiring Harness, # 118266. This kit gives you all of the necessary harnesses and relays that you will need for a fully functioning 7-way trailer connector except for the brake controller.
I have attached the installation instructions for this kit for you to check out.
Once you have this kit installed, you will need a brake controller and a brake controller wiring adapter. For a... view full answer...
The suspension travel on your 2018 Nissan Frontier SV will not be great enough to create any issues for the Firestone Ride-Rite Air Helper Springs part # F2558 which are a confirmed fit. You are also correct that the Daystar Cradles are used mainly for lifted vehicle applications and will not be needed on your stock height Nissan Frontier. view full answer...
Westin Fey Universal Rear Bumper # 66000 is a general-purpose part intended for use on many different older vans and pickups starting with late-70s model years. It does not offer a custom-fit on any one vehicle so some modifications to a compatible vehicle and/or the bumper itself are required. It may be usable on a Frontier but we offer no install kit for your vehicle.
We do not have a custom-fit replacement bumper for your Frontier but we do have other custom accessories like tube steps,... view full answer...
I recommend the etrailer Trailer Hitch Receiver # e98869 for your 2023 Nissan Frontier. This receiver is custom fit and has a matte black finish for a factory appearance. There is a tab welded on the receiver that will accept the 4-way Mounting Bracket # 18144 or the 7-way Mounting Bracket # PK12711U depending on the wiring kit you require.
The Wiring Harness # 118266 will give you a 7-way connector to fit your Frontier. The kit includes the necessary relays to activate the factory tow... view full answer...
Although some additional parts are required, it is possible to use the # 8523163001 to add locks to your Thule TracRac TracONE # TH27000XTB. You will need the following to add locks to your ladder rack:
-Rail Clamp - # 8523159002 (Quantity of 2)
-T-Slide Casting - # 8523164001 (Quantity of 2)
-Socket Head Cap Screw - # 8523233001 (Quantity of 2)
-Clamp Lock Housing - # 8523163001 (Quantity of 2)
-One-Key Lock System - # TH450200
You will use one of the new clamps on the front and... view full answer...
Yes, you can use the DeeZee truck bed mat part # DZ86965 in the bed of your 2022 Nissan Frontier without a tonneau. It weighs enough and fits well enough that it would not catch wind and fly out. view full answer...
The Aries Round Nerf Bars # AA204046-2 you referenced use the replacement mounting bracket kit # AABRKT-204046 but this kit is designed for a 2007-2019 GM truck.
Since you have a 2006 Nissan Frontier you need a different set of nerf bars and mounting hardware for them to fit properly. If you want the polished stainless steel style like what you mentioned having then you need part # AA209019-2, otherwise we have part # AA209019 which is a semi-gloss black powder coat instead.
Both of these... view full answer...
It sounds like your Tekonsha Voyager Trailer Brake Controller # 39510 is faulty. While the controller is proportional and will not send power to the trailer brakes when parked by using the manual slide knob it should send power to the brakes even when not moving. Since you have the green light on the controller it senses there is a trailer connected. You can choose to bench test the controller by connecting the black wire to 12 volt power, white wire to ground and using a 12 volt 1156 Incandescent... view full answer...
Go To Results