When it comes to wind screen fairings for your Thule aeroblade roof rack, I recommend The AirScreen XT # TH82WV for Thule Crossbars. The aerodynamic fairing will deflect air over your roof rack to reduce wind noise and drag. They're 44 inches long x 5-1/2 inch tall by 2 inches wide.
I will put a specs review video below. view full answer...
To make the LED trailer tail lights work with the factory trailer wiring on your 2011 Mercedes ML550 you will need a Trailer Connector Adapter w/ Lamp-Out Sensor Bypass # 20142. This will plug into your 7-way on your ML550 and allow the trailer to plug into it. The adapter tricks the computer in your Mercedes to believe that the trailer does have normal incandescent bulbs so that you do not get the bulb out error on your dash.
If you are hauling a smaller trailer the 7-Way to 4-Way/5-Way... view full answer...
At this current time we do not have a trailer hitch yet confirmed to fit your 2023 Mercedes-Benz E-Class. For the time being if you're trying to haul bikes I recommend The Yakima FullBack 2 Bike Rack # Y02634.This rack can hold up to two bikes weighing 35 pounds apiece.
If you could reach back out to me on what you're trying to use the hitch for I may be able find other solutions for you. view full answer...
When it comes to hauling your Kuat bike rack with your Ford Truck with a 3 inch hitch you will not be able to stack 2 of The Kuat Magnetic Hitch Receiver Reducer Sleeve # KU93VR together. Per the manufacturer it is not designed to be stacked together and it would not work properly. The Curt Hitch Receiver Reducer Sleeves # C45408 is what you will need. Using this adapter will reduce your 3 inch hitch to a 2-1/2 inch or 2 inch receiver and allow you to use your Kuat rack and anti rattle... view full answer...
I would be happy to help you find a hitch receiver for your 2021 Mercedes-Benz Sprinter 2500 van with a factory step. In order to haul a trailer you are going to need a wiring harness as well. The Curt item # 13358 you were looking at is the best hitch receiver available.
I highly recommend it based on its ease of installation, weight capacity, and the built in bracket for attaching a wiring harness. The Curt Trailer Hitch item # 13358 has a maximum gross trailer weight of 5,000 lbs and... view full answer...
For your 2019 Jayco Melbourne, while we do not offer a 2-bike trike bike rack we do have another solution that may work for you.
Instead, check out the:
-Swagman RV 4-Bike RV Bumper Mount Rack # S80600 with the tie downs # 05605.
This platform rack will allow you to carry up to 4-bikes, has a weight capacity of 120-lbs, and is made for welded steel square bumpers that are at least 4" wide and no wider than 4-1/2".
I have also attached a product review video for you to check out as well. view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13018 uses M14 x 5.50 grade 8 bolts. There are replacement hardware kits available for the Curt # 13018 by putting that part number into the field marked "Hitch Item Number" on the page for the # RHK.
I've also linked the instructions for this hitch that list the specs of the bolts and the washers. view full answer...
I completely understand your frustration and need for simplicity. I recommend the Curt Echo Wireless Trailer Brake Controller item # C51180. This bluetooth-enabled brake controller wirelessly connects to your smartphone, allowing you to control your trailer's brakes from your phone. The compact unit plugs in line with your 7-way trailer connector at the rear of your vehicle. This is a proportional brake controller that activates your trailer's brakes based on the deceleration of your vehicle.... view full answer...
Yes, we do sell a hitch that is compatible with the factory step bumper on your 2020 Mercedes-Benz Sprinter 2500. It is the Draw-Tite Max-Frame Trailer Hitch Receiver item # 75601. This hitch is custom fit and designed to fit the 144WB of your Sprinter van. I have attached an installation video.
This hitch also comes with a bracket to mount a 7-way vehicle connector. I recommend the Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter - 7 Way Trailer Connector item... view full answer...
The Curt Class III 2 Inch Hitch, part # C13010 will fit your 2010 Mercedes-Benz G-Class vehicle. A hitch ball is only needed if you will be towing a trailer. The hitch ball is located on a ball mount that fits into the trailer hitch. It is where the trailer coupler would connect to the trailer hitch. A hitch ball is not needed if you will only be using the hitch for a bike rack.
Since you will be using the Curt hitch for non-trailer loads like a hitch bike rack, you will need to use a... view full answer...
The ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 19250KIT is confirmed to fit your 2015 Mercedes-Benz GLK Class.
This harness will work on vehicles and trailers with either LED, incandescent, or standard bulb tail lights. This harness may be used on 2 and 3-wrie systems. The tail light circuit is upgraded to work with vehicles using the Pulse Width Modulation, which allows the converter to fully turn on, giving the trailer lights... view full answer...
It sounds like you're in need of the Wheel Masters 2-Hose Inflation Kit - 16" to 19-1/2" Inner Dually - Hand Hole Mount # WM8009, which will work on 16" to 19-1/2" inner dually wheels to allow you to check the air pressure and inflate the tires as needed. These are stainless steel wrapped, so they've going to be protected from the occasional pinch and other wear and tear that might ruin simple rubber valve extenders.
I've linked a review video on these for you to check out, and they come... view full answer...
If the bolts on your Curt Trailer Hitch Receiver - Custom Fit - Class III # 13358 are a little over torque that is not a big deal and should not pose an issue.
If you don't feel good about it and would rather just replace the hardware, you are going to need M12 x 1.75 Hex bolts, with a .375 x 1.25 x 2.00" round hole spacer, with a M12 x 1.75 flange nut.
Or
You can use our replacement hardware kit # RHK which will contain all the needed hardware for installation. For the "hitch item... view full answer...
With the Curt Hitch # C84ER installed on your 2021 Mercedes-Benz GLC Class all three bike racks you looked into will work for your vehicle. I recommend The Thule Apex XT # TH9024XT. The Thule bike rack has the tilting feature which makes it easier to load and unload the bikes from the rack. It can hold up to 37.5 pounds per bike, and only weighs 35 pounds.
I would also recommend The etrailer Hitch Receiver Lock # e98881 to help with security of your bike rack. I will attach a install... view full answer...
Wheel Masters makes Support Brackets for Rubber Valve Stems # WM8029VS on 16" wheels, that you can use with the Wheel Masters 4-Hose Inflation Kit # WM8001 on your 2017 Airstream Interstate RV. view full answer...
You will want to go with the larger 60" Thule WingBar Evo Crossbars # TH711520. Then you will also need Rapid Podium Feet # TH460R and Fit Kit # THKIT3101. I attached a demonstration video for you to check out. view full answer...
In addition to the # TH711200 and # TH460R you will also need the foot pack # THKIT4049 to complete your roof rack kit.This will give you a great looking roof rack with aerodynamic crossbars that will reduce wind noise that normally comes with installing a roof rack.
With that said, the issue you're going to run up against is twofold. First, the crossbars are only 47" long, and fitting 3 kayaks is going to be a tight squeeze on those bars; secondly, although the # TH711200 crossbars have... view full answer...
I do have a solution for you but none of our other ladders have as tight of a return as the Surco Universal Exterior RV Ladder # SP502L that you referenced.
Since you basically just need the Surco ladder but just a little longer I recommend using either the Surco RV Ladder Extension # SP504L which is 30-1/2" long or the Stromberg Carlson RV Ladder Extension # LA-148 which is 48" long. The Surco rests on your RV but the Stromberg Carlson rests on the ground. view full answer...
We can help you upgrade the trailer wiring on your 2012 Mercedes-Benz GLK 350 to the 7-way type to enable use of a trailer brake controller like the excellent Prodigy P3 # 90195.
Kit # ETBC7 includes a 7-way vehicle socket and all of the connectors and components needed to install a brake controller. This will be a hardwire installation as shown in the linked article and video which shows a Mercedes-Benz install.
You can avoid the connection issues and hassles of using wiring adapters... view full answer...
The Curt Sway Control # 17200 is designed to be used with weight distribution systems. If you're not interested in a weight distribution system you can use the Reese Sway Control # 83660 with a bracket.
For the bracket use # RP26003 and for a Class III and larger hitch receiver or # RP26005 for Class II. view full answer...
Go To Results