Expert Answers about Mercedes-Benz Sprinter
- Recommended Swing-Away Adapter For A Hollywood Racks Sport Rider SE Bike Rack
- What we have for your Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes # HLY84FR is the:
-Yakima BackSwing Swing Away Hitch Extender for Bike Racks # Y02483.
This adapter will fit into 2" x 2" hitch receivers, has a 250-lbs weight capacity, and measures 30" wide x 20" long x 8" tall.
view full answer... - Is There a Way to Trick Parktronic Sensors on a 2016 Mercedes-Benz Sprinter for a Bike Rack
- I am not sure if this will have enough draw but we have testers like the Curt LED Tester # I26 which puts a small load on a 4-Way Flat connector. This is used to make sure that your wiring is working correctly but it may be enough to trick your sensors.
If you have a 7-Way then I recommend using the Tow Ready # 20142 as it will simulate a draw as well.
Please note that both of these products are designed to be plugged in for short periods of time and haven't been tested for prolonged...
view full answer... - Replacement Ladder Needed with Tight Return at the Top
- I do have a solution for you but none of our other ladders have as tight of a return as the Surco Universal Exterior RV Ladder # SP502L that you referenced.
Since you basically just need the Surco ladder but just a little longer I recommend using either the Surco RV Ladder Extension # SP504L which is 30-1/2" long or the Stromberg Carlson RV Ladder Extension # LA-148 which is 48" long. The Surco rests on your RV but the Stromberg Carlson rests on the ground.
view full answer... - Recommended Inner Dual Wheel Valve Extenders for 2013 Winnebago View
- It sounds like you're in need of the Wheel Masters 2-Hose Inflation Kit - 16" to 19-1/2" Inner Dually - Hand Hole Mount # WM8009, which will work on 16" to 19-1/2" inner dually wheels to allow you to check the air pressure and inflate the tires as needed. These are stainless steel wrapped, so they've going to be protected from the occasional pinch and other wear and tear that might ruin simple rubber valve extenders.
I've linked a review video on these for you to check out, and they come...
view full answer... - Bearing Kit for 3,500 lb Trailer Hub
- Thanks for that detailed information and we have exactly what you need with Bearing Kit # BK2-100. This kit includes Bearings # L44649 and # L68149, Races # L44610 and # L68111, along with Grease Seal # 58846.
This kit is for 3,500 lb hubs like yours, which would be Trailer Hub and Drum Assembly for 3,500-lb Axles # 84546UC3 or, if you had an E-Z Lube axle, the Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles # AKHD-545-35-EZ-K.
Typically when hubs are "spitting" grease it is...
view full answer... - Complete Trailer Brake Controller Setup for a 2012 Mercedes-Benz Sprinter Without Tow Package
- For your 2012 Mercedes-Benz Sprinter you can absolutely use the Tekonsha Prodigy P2 Trailer Brake Controller # 90885 you mention.
This brake controller has 3 boost levels to allow you to fine tune your initial braking power, an auto-dimming LCD display that is easy to read, and includes the mounting bracket and hardware for install.
You are also correct in the fact that you're also going to need to add the Universal Installation Kit for Trailer Brake Controller # ETBC7. This kit will...
view full answer... - Wiring Harness That Includes Reverse Light Signal for Trailer Coupler Electric Lockout
- You can have a reverse light signal for a trailer's hydraulic coupler lockout in either the 5-pole or 7-way wiring formats.
If a vehicle has a basic 4-pole harness like # 118650 that fits your 2011 Sprinter you can add another circuit for the reverse light signal simply by adding 5-pole adapter # 20036. This wires to the reverse lights to get you the signal you need. Please see the linked videos.
A 7-way has a reverse light signal carried on the center contact as shown in the linked photo....
view full answer...
Go To Results