The crosstube on the Draw-Tite # 65076 and Curt # C31078 front hitch receivers for your 2018 Ford F-250 Super Duty are at different locations than the mounting brackets connected to them. To really determine where the hitch pin hole will be we need to measure where it's at in relation to a corresponding mounting bolt hole.
For your application you'll want to go with the Draw-Tite hitch which has the hitch pin hole 4-1/2" in front of the forwardmost mounting hole (see attached). I wasn't... view full answer...
We have the FloTool RhinoRamps part # FT11912MI which are rated for 16,000 lbs. It provides a lift of up to 6-1/2 inches and works on up to 10 inch wide tires. view full answer...
We sell baby moon covers for the Dexstar conventional wheel part # AM20504 like with the part # AM90086 but we do not have any trim rings that go around the outside. The weight capacity of this wheel is 1,820 lbs per wheel. view full answer...
Thanks for the picture! The 3rd Brake Light Logic Module item # PP20-702 you were looking at is exactly what you need to activate a third brake light on your 2022 Ford F-150's Overland camper topper. Once connected, this module allows the third brake light to illuminate separately from the turn signals. Without this module the third brake light would blink when the turn signals are illuminated.
I attached a wiring diagram below which shows how to wire this module into your F-150's tail... view full answer...
The Spring Bars # BLU82FR for the Blue Ox TrackPro Weight Distribution # BLU36FR is what gives you the tongue weight range of 200-600lbs. The adjustment holes for the ball mount itself are only to help you level the trailer. There are bolt holes on the L-Brackets # BLU72QR for the trailer which will allow you to increase or decrease the amount of tension on the bars. These are typically only ever used in one mounting position. Personally I have never been a fan of the Blue Ox weight distribution... view full answer...
I recommend using the Master Lock 1-9/16" Wide Solid Brass Body Padlock # ML140DLH with the Hitch Pin # RM-910044 for the Roadmaster D-Ring Adapters # RM-035-1. The locks have a 1/4" diameter that will fit inside the Roadmaster pin. This will be much easier to fit with the tow bars on your d-ring bumper connections.
The InfiniteRule Locking Pins # IR44FR will be difficult to position in the pin with the tow bar taking up the narrow 1-1/2" measurement you have. We currently do not have... view full answer...
I'm not 100 percent certain if you are asking what the rating is or stating what the rating is for a cable, but the bottom line is that the Roadmaster 68" Single Hook, Coiled Safety Cables # RM-643 are rated for 6,000 lbs each, but that does not mean two of them give you a 12,000 lb capacity because if one were to break the capacity is 6,000 lbs and that is what the rating is for.
I have added a link to a video review of these cables for you as well as a link to our entire selection of... view full answer...
The capacities we have listed for the Gladiator Utility Cargo Net - Cam Buckle Tie-Downs - Roof Rack/SUV - 4' 9" x 5' 3", part # GC77FR, correspond to the maximum load (break strength) when using this cargo net without the cam buckle straps, 4,500 lbs, or with the straps, 3,969 lbs. You should adhere to the safe working load limit of 1,500 lbs, without the cam buckle straps, or 1,323 lbs, with the cam buckle straps. view full answer...
The Blue Ox Weight Distribution kit part # BXW1006 that you referenced comes with a shank that provides up to 13 inches of rise. This would be basically exactly what you are in need of without requiring a different shank. view full answer...
The Reese Strait Line system part # RP66084 would work well for a trailer like your Airstream that weighs 9,500 lbs. This has a tongue weight range of 600-1,200 lbs and has best sway control at fight sway before it starts. Typically a trailer's tongue weight is 10-15 percent of the total trailer weight this would work great or what you have. view full answer...
The Lippert 2" Trailer Hitch Receiver # LC730647 weighs approximately 45-lbs and can be installed by bolting it on to the frame of your travel trailer or RV to allow you to carry hitch mounted accessories rated for use on the back of an RV or travel trailer. This hitch has a heavy-duty powder coated finish to help protect against rust and corrosion. view full answer...
The Reese 5th Wheel Trailer Hitch part # RP30047 has dual locking jaws which are 1/2" thick. If you are looking for something beefier then I recommend the Curt A16 5th Wheel Trailer Hitch part # C16120 which has dual interlocking jaws which are 1" thick. The Curt A16 also has a much tighter fit around the kin pin therefore less movement occurs and you receive a better ride quality. The other thing I really like about the Curt A-16 is that it has a one pin head removal system that makes... view full answer...
I have a solution for you but Demco does not have a baseplate kit for a 2023 Ford Bronco. However, if you are using a Demco tow bar there is an adapter available that will work with the item # RM79RR baseplate you were looking at. It is the Demco Tow Bar Adapter Kit for Roadmaster Direct-Connect Base Plates item # DM9523032.
I have linked an installation video below so you can see this adapter being used.
The Roadmaster Direct-Connect Base Plate Kit item # RM79RR is confirmed to fit... view full answer...
With the Titan Chain Snow Tire Chains w/ Cams for Dual Tires - Ladder Pattern # TC4819CAM that you referenced the max speed rating is 30 mph. view full answer...
So the ideal amount of clearance between the trailer overhang and the bed rails of the truck is 6 inches while the trailer is sitting as level as possible. If your trailer sits perfectly level and you currently have 5 inches you probably will be fine as long as you don't plan to travel on any extreme elevation changes. Some say that 4 to 6 inches is okay but we tend to have people shoot for 6 inches to be extra safe.
But let's say you can raise the nose of your trailer up to get it level... view full answer...
For Pipe Mount Swivel Jack # TJP-2002S-B the distance from the center of the pipe mount up to the top of the gearbox is 6-1/2-inches. From the center of the pipe mount up to the highest point of the handle rotation the distance is 12-inches. Overall length from the foot plate to the top of the gearbox is 21-1/2-inches with the jack fully retracted.
Additional dimensions are shown in the linked photo. view full answer...
The SnowBear Proshovel Snowplow for 2" Hitches - Electric Actuator - 88" Wide x 26" Tall item # SB324-140 needs to be mounted 9"-10" above the ground. There is an extension kit if your Ford F-250 is lifted or sits to high. It is the Drop Extension Kit for SnowBear Snowplows - Bolt On - 3" Drop item # SB324-128. This bolt-on kit ensures that the plow makes proper contact with the ground. Its sturdy steel construction is just as strong and durable as the plow itself. view full answer...