I went out to the warehouse and pulled one of the Pro Series Snap-Ring Swivel Jacks, # PSEJ10000101, to measure for you. I added dimensions to a photo I took of the mounting plate for you to use to see if the mounting pattern will match up to your mounting plate on your LAK sailplane trailer model T-5.
The overall dimensions of the mounting plate are 6-3/8 inches by 5-1/2 inches, and the bolt hole pattern is 4-3/8 inches on center for the outer most holes, 3-3/8 inches on center for the... view full answer...
The etrailer Tongue Weight Scale # e99044 will give you a good idea on tongue weight, but if you're looking for high accuracy I would find an alternative. There is no accuracy rating available for this scale. It will give you a ballpark idea but in your case where a slight difference matters it is not the best choice. You should find a scale with more tick marks or digital readout so you know exactly where you're at. view full answer...
I pulled a Camco Propane Cylinder Gas Gauge and Leak Detector # CAM59023 from our warehouse to measure its length and determined that it is 3-3/4 inches in length. view full answer...
The valve stem of this Americana Metal, Bolt-In Valve Stem # AM20906 that you referenced is 1-1/4 inches long in overall length.
I attached an FAQ on trailer tires for you to check out also. view full answer...
Since we do not currently have a confirmed fit the easiest way to figure out which Coil SumoSprings will fit your 2014 Ford Expedition is to measure the gap between in the middle of the coil, pictured below. This will need to be done while the vehicle is on the ground with the full weight still placed on the axle. Once we have that measurement I can find the correct Coil SumoSpring for your application.
For example the Coil SumoSprings Custom Helper Springs for Coil Spring Suspension... view full answer...
The 1999 Ford Expedition most likely has a class III rated towing package from the factory. In order to determine which class you have, you can check the trailer hitch for capacity information. There is usually a sticker on the hitch that will list trailer weight and tongue weight capacities.
If it reads 3500 pounds or more and the hitch has a 2 inch receiver opening, you have a class III trailer hitch. You also may be able to find the information in the owners manual for the vehicle... view full answer...
To flat tow a 2019 Ford Expedition Max 2WD you will need the following parts:
Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item # e84ZR
Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms item # RM-524457-5
Wiring Harness - Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267
Charge Line Kit - Roadmaster Battery Charge Line Kit for Towed Vehicles item # RM-156-25
Supplemental Braking System - Blue... view full answer...
Weight distribution spring bars simultaneously pull down on the trailer ferame, which increase the weight on the hitch ball, and lift up the weight distribution head that the ball is on, which basically cancels out any additional weight that was put on the ball.
When the system is set up properly the tongue weight of the trailer should stay roughly the same though it will likely be a little higher. Provided that the tongue weight is within the capacity of the hitch to start with you won't... view full answer...
In the answer page you're referring to Conner didn't say the hub face to brake flange is useless. He said measuring from brake flange to brake flange (from one side to the other) isn't really helpful when choosing a replacement axle. The 2 most important measurements are hub face and spring center distances.
With that being said, the replacement spindles # TRU77FR and # TRU74FR will have matching distance from the hub face to the brake flange because they are both modern #84 spindles so... view full answer...
The Semi-Custom All Weather Rubber Cargo Mat part # 4601200 for black measures 54-1/2" long x 49-1/4" wide. The cargo mat is a semi-custom option which means you would need to trim this to fit your cargo area.
If you are looking for a custom fit option that does not require trimming, I recommend the WeatherTech Cargo Liner part # WT40488 if you have 3rd row seating or part # WT40489 for 2nd row seating. view full answer...
I confirmed with my contact at Aries that the spacing of the pre-drilled holes on the Aries Bull Bar # AA35-3007 (not the mounting holes) are 14-1/2 inches apart. I went ahead and included a diagram of the dimension for better perspective.
If you find out that you are having difficulty in finding LED lights that fit those dimensions, we do carry the LED Light Bar Mounting Brackets for Aries Bull Bars, Grille Guards, and Headache Racks # AA1110312 along with the Aries 20" Single-Row LED... view full answer...
The weight of the Flow Through Tire Sensors for TireMinder TPMS # TM66FR is 0.7oz each including the CR1632 battery. According to TireMinder, these should not throw off the balance of your tire. That being said, you could always have them checked at a local tire shop for peace of mind once the sensors are installed. view full answer...
Dexstar Steel Mini Mod Trailer Wheel # AM20545 does not have any offset. I confirmed this with Dextsar. It sounds like you are asking about the backspacing which is the distance from the mounting flange to the outside of the rim.
Since this is a 6 inch wide rim the back spacing is 3-1/2 inches. To determine this you take the overall width of the rim and add an additional inch for the lip on the wheel and then divide by 2. view full answer...
I pulled the Curt Bumper Mount Hitch, # E-3S, from the warehouse and made a video showing you the measurements that you were asking for. The wider holes, closest to the receiver opening, are 1-1/4 inches wide and accept a 3/4 inch diameter bolt. The bolt holes measure 10-3/4 inches at their widest points and 7-1/4 inches at their closest point.
With the bolts set at the widest point, they measure 9 inches apart on center and 8 inches apart at the closest point. view full answer...
The mounting holes in the 4-Pole Flat Mounting Bracket, item # 18144, are 1-3/4 inches apart.
The bracket is 2-1/4 inches wide overall and comes with two self tapping screws and two Phillips head stove bolts and nuts.
A No-Drill Mount Bracket, Long # C57202 or Short # 18140, is available to attach the 4-Pole Flat Mounting Bracket to the trailer hitch and eliminate the need to drill. view full answer...
I've reached out to WeatherTech in the past for mat dimensions and their response is always that they custom fit each mat to fit each application exactly so the WeatherTech Cargo Liner - Cocoa # WT43322 will fit like a glove to the rear cargo area on your 2017 Ford Expedition (they don't provide dimensions). The typical photo on the product page doesn't reflect the exact shape of the liner but if you notice there is a lip that fits snug against the seats and sides of the cargo area so that... view full answer...
I attached an FAQ that details how to pick out the correct ball mount. Picking out the correct ball mount will allow your trailer to sit as level as possible. Basically you will first measure the height from the ground to the top of the receiver opening on the hitch while on level ground. Next, you will measure the coupler height from the ground to the bottom of the trailer coupler when the trailer is on level ground.
Next, you will need to compute the difference. If the hitch height is... view full answer...
I went out to the warehouse to check the wire gauge used on Hopkins Endurance Easy-Pull 4-Way # HM48138. The ground wire is 16 gauge and the light wires are all 18 gauge. These are common sizes used on 4-Way harnesses. view full answer...
Go To Results