In regards to setting up a weight distribution system like the Curt MV Weight Distribution System part # C17062, it is advised that you make any adjustments needed to the tow vehicles suspension first and then set the head tilt or spring bar tension on the weight distribution system.
I can't speak to every type of system such as the adjustable leaf springs you have but if you were using air bags for example, you would attach the trailer and then adjust the psi until you're as close to... view full answer...
You certainly can install a replacement 5.2K axle like # 6340624 by using new spring seats atop the axle. I'd recommend using part # TRSS300 but it's recommended that they at least be tacked into place so they stay put. view full answer...
The tires on your trailer should not come off the ground while leveling. It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix your issue then please just let me know and I will see if we have any other actions for you to perform.
1. Manually run the jacks to level the unit. This is best achieved by placing a level in the center of the unit and leveling it both front... view full answer...
Reese recommends that when you install the bolt on chain hangers part # RP58305 that they sit 1/4 inch down from the top of the frame if the frame is a box frame or 1/2 inch down if it's a c-channel. It is important you follow these instructions. If you already installed them in the wrong location you should reinstall them where they need to go. view full answer...
While I won't be able to tell you the exact length cable you'll need I can help point you in the right direction. The first step is going to be to figure out exactly how your current valve is mounted so that you can remove it and choose the correct replacement.
The LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank # 34466N4AB36GM you were looking at is a Spigot to Hub design. The spigot end with sit inside of a hub and the hub end with sit over a pipe. The hub and spigot... view full answer...
The reason why the Everchill RV Refrigerator w Freezer Drawers # EV87FR cutout is quite a bit larger than the fridge itself is for ventilation and heat dissipation. The installation calls for at least 11.8" of free space on the top, 3.9" on either side, and 2" on the back for heat dissipation space. view full answer...
I do have some advice for you but we don't carry any spindle shims for the castle nut. I've messed with many spindles and castle nuts, there are a lot of times it seems there is one notch that's too loose and one that's too tight. I recommend the slightly tighter setting if needed, you don't want any side to side play in the hub when tight. This can cause grooves to wear into the spindle over time and destroy the axle. view full answer...
Yes, it is a good idea to go ahead and add grease when installing the Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links # AP233.
You don't want to use fat though, just go ahead and use the LubriMatic Multi-Purpose Lithium Grease # L11316. view full answer...
The Flow Max RV Kitchen Faucet part # LC719325 is made by Lippert who is an OEM manufacturer so this is likely what you have. If the faucet is leaking it will need to be replaced as there are no replacement parts offered for it. It should be pretty easy to replace yourself. view full answer...
The RV Refrigerator Roof Vent Cap and Base # DMC37FR comes with the vent cap and the base. Installation hardware is not included.
We do have installation hardware available. The Camco RV Vent Installation Kit # CAM25013 if you have a rubber roof or the Camco RV Vent Installation Kit # CAM25003 if you have a metal roof. You would also want some LaSalle Bristol XTRM Universal Self-Leveling Sealant # 34427034145-1.
We also have the Roof Vent Installation Kit # 344270KITW which includes the... view full answer...
You will need a minimum of 3 inches, it is best to install the Solera RV Slide-Out Awning, # LCV000165062, in the 3-6 inch range above the slide out for proper clearance and angle, above 6 inches becomes to steep. Please note the attached installation video for additional valuable information. view full answer...
It sounds like your awning might not utilize locking pins and in which case you'd need to do some modifications to install the RV Awning Locking Pins part # 3721164. I have attached the steps for this below. view full answer...
I have actually spoken to my contact at Performance Tool before about the possibly of overcharging with the Solar Battery Charger # PTW2997. He said that this unit does feature a built-in control that will shut the charger down when the battery is completely charged. There is no risk of overcharging the battery even if you were to use this for a longer-term application such as when the camper is in storage.
I have attached a short video demonstration on this charger that you can check... view full answer...
The Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents # MA10-20281K-1AF is the correct lift operator for a number of MaxxAir fan's (4500K - 4900K, 4700N, and 4900N) and is likely the correct lift operator for your MaxxAir fan.
The lid is often times riveted to the mounting bracket, but then the mounting bracket is secured to the fan housing with screws. I suggest opening the lid and accessing the screws securing the lid mounting bracket to the fan housing. view full answer...
Never fear! I went ahead and reached out to my tech at Valterra (the manufactures of Mighty Cord products) and she confirmed that the RV Power Cord Adapter # A10-5030FBK takes the 240v down to 120v. This this factor, it is fine to use with a 30-amp RV. view full answer...
I do have some information for you that should help but unfortunately we have not yet had the chance to install the Global Link RV Entry Door Locking Latch Kit part # 295-000021 on a blank door so we do not have an install video. It's a pretty simple install that I think you'd be able to handle pretty easily. Basically, you will want to mark a cutout about 2-1/2" wide x 3-1/2" tall in the face of the door near the edge where you want the handle to be and then use something like a dremel... view full answer...
The only true way to determine the function of a wire or pin on a 7 way plug is to test it using a circuit tester like the Cordless Circuit Tester # PTW2979; unfortunately colors are not standard or a reliable way to determine function.
If you're going to be adding a new 7 way connector like the 7-Way Molded Trailer End # 54006-009 to your trailer, you'll want to connect each wire to a battery and ground to determine which function is activated when power is supplied. Once you're determined... view full answer...
The standoffs/nubs on the backside of the Lippert RV Entry Screen Door Latch # LC201471 that you referenced can indeed just be sanded off or cut off so that it can lay flat against your door. This right hand latch will install on the left hand side of your door.
I have attached a video demonstration that you can also check out. view full answer...
The MORryde X-Factor Crossmember part # MR33WR attaches to the leaf spring hangers which are located in-between and in the front and rear of each axle. I have attached a photo below to clarify. Therefore, you'll need three for full support on a tandem axle trailer. view full answer...
There are only two types of cameras available for the Furrion Vision S Wireless RV Observation Camera System part # FCE48TASL-05. There are traffic cameras with integrated side marker lights and there is the main overhead camera. The system comes with three cameras but has the capacity for up to four so you can add the Furrion Vision S Wireless RV Backup Camera part # FCN48TASF and use it how you like. There isn't a license plate bracket for this camera but you should have no issues finding... view full answer...
Go To Results