Should Bolts of AP233 Suspension Kit be Greased

Question

Question:

Hello if I order the Suspension Kit for Tandem-Axle Trailers - 1-3/4inch Wide Double Eye Springs - 2-1/4inch Links Item # AP233 Do I need to grease the bolts before installing them? if yes, with what fat? thank you

asked by: Pierre

0

Expert Reply:

Yes, it is a good idea to go ahead and add grease when installing the Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links # AP233.

You don't want to use fat though, just go ahead and use the LubriMatic Multi-Purpose Lithium Grease # L11316.

expert reply by: Kyle S

0

Answer 1

Trailer manufacturers don't usually keep a record of parts like these that they install at the factory, so I cannot be sure as to the exact length of the shackle strap that would have come originally on your trailer. With this in mind, a…

view full answer...

Answer 2

As long as the new equalizer has the same hole spacing as the existing equalizer, it'll work just fine. You'll also want to make sure the height of the equalizer is also the same. Put a ruler across the center of the two bottom bolt…

view full answer...

Answer 3

For a 5,000 lb trailer the dolly solution would be the Rack'em Dolly part #RA20 which has a 500 lb tongue weight capacity. If you wanted something that would make moving the trailer a little easier the Trailer Valet XL part #TVXL25 for if…

view full answer...

Answer 4

Sometimes this happens when the brake assemblies are installed on the wrong side of the trailer. I'd check to make sure they are both installed on the correct sides.

view full answer...

Answer 5

In regards to trailer suspension kits like the Suspension Kit for Tandem-Axle Trailers part #AP233, the shackle bolt heads are indeed seating into the hangers via the knurling on the bolt. If you hold a wrench on the bolt head and tighten the nut,…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 8

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 9

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 12

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Should Bolts of AP233 Suspension Kit be Greased

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching