Where Do the MORryde X-Factor Crossmembers Install

Question

Question:

Does this item go between spring hangers just where the spring equalizers sit on each side or do you place one at each spring hanger?

asked by: Melvin D

0

Expert Reply:

The MORryde X-Factor Crossmember part # MR33WR attaches to the leaf spring hangers which are located in-between and in the front and rear of each axle. I have attached a photo below to clarify. Therefore, you'll need three for full support on a tandem axle trailer.

expert reply by: Conner L

0

MORryde X-Factor Crossmember Diagram
(click to enlarge)

Answer 1

The MORryde X-Factor Crossmember part #MR33WR is designed for standard suspension so that is the one you will need to use. If your leaf spring hanger brackets are wider than 3" then you will need to drill per the instructions which I have…

view full answer...

Answer 2

You can use that upper hole on your hanger to install the #MR33WR. Make sure you don't tighten it down too much or you will pinch the leaf spring and it won't function properly. You will also need to make sure you have enough room to install…

view full answer...

Answer 3

I spoke with MORryde and they said that the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR will work just fine with your frame hangers with gussets. You'll just need to use the circled items attached in the image below and…

view full answer...

Answer 4

Thank you for the images. The MORryde Rubber Equalizers #MR87ZR are the correct set for your 2020 Keystone Outback Ultra-Lite 291UBH. You will pair this with the MORryde Suspension Upgrade Kit #MR46ZR. Instead of using the wet bolts included with the…

view full answer...

Answer 5

It is likely you can avoid the drain line when installing the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR by using the MORryde X-Factor Crossmember Adapter Kit for Drop Down Applications #MR43WR. I don't know exactly the…

view full answer...

Answer 6

The MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR includes one adjustable crossmember. Your existing hardware will be too short due to the extra thickness of the crossmember, so you will need to add #MR58ZR if…

view full answer...

Answer 7

MORryde has a version of the X-Factor Crossmember that was designed to work with the CRE3000 you have with the part #MR33WR.

view full answer...

Answer 8

Kenny, those bolts for the B&W Companion 5th Wheel Trailer Hitch #BWRVK3500-5W should be torqued to 40 ft. lbs. Also, the pivot arms would need to be torqued to 80 ft. lbs, the draw down bolt should be tighten to 60 ft.lbs and the arms should be…

view full answer...

Answer 9

The Triangular Equalizer #TREQ310 is a replacement for the Dexter 13-10 on your 2022 Nash 23D travel trailer. You should consider upgrading to the MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR. These will pair with either the 2-1/4"…

view full answer...

Answer 10

Yes you can just use one MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR with your 2021 Jayco Jay Feather 25RB, however for full support a tandem axle trailer will need to utilize 3. Attached is a product overview…

view full answer...

Answer 11

I went ahead and reached out to my contact at MORryde, and she confirmed that the X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR will come with new mounting hardware. The plates on the cross member do add thickness, so the…

view full answer...

Answer 12

The MORryde X-Factor Crossmember #MR99ZR is designed for LRE, RE, or TRE Leaf Spring Suspension systems so since you're using the Dexter E-Z Flex Suspension Kit #K71-653-00 you'll want to use the MORryde X-Factor Dropdown Crossmember #MR84AR…

view full answer...

Where Do the MORryde X-Factor Crossmembers Install

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching