Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Item # 13650
Our Price: $220.35
Confirmed to Fit
2005 Ford Escape
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (520)
- Q & A (0)
- Photos
2005 Ford Escape - Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- 2 Inch Hitch
- Class III
- 3500
- Visible Cross Tube
- CURT
- 350
- 5000 lbs WD GTW
- 500 lbs WD TW
- Custom Fit Hitch
This fully welded trailer hitch receiver bolts onto your Ford Escape's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
- Custom fit is designed specifically for your vehicle
- Precision, robotic welding maximizes strength and improves fit
- Bolt-on installation - no welding required
- Complete hardware kit and installation instructions included
- Lifetime technical support from the experts at etrailer.com
- Gloss black powder coat finish over protective base coat offers superior rust resistance
- Stylish, round-tube design
- Ball mount, pin and clip sold separately
- Hitch assembled in the USA, bolts overseas
Specs:
- Receiver opening: 2" x 2"
- Rating: Class III
- Maximum gross trailer weight: 3,500 lbs
- Maximum GTW when used with weight distribution: 5,000 lbs
- Maximum tongue weight: 350 lbs
- Maximum TW when used with weight distribution: 500 lbs
- Maximum gross trailer weight: 3,500 lbs
- Limited lifetime warranty
etrailer.com Technical Support
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
13650 Curt Class 3 Trailer Hitch Receiver
Installation Details
Weight Carrying Capacity
Gross Towing Weight (GTW):
3,500 lbs.
Tongue Weight (TW):
350 lbs.
Weight Distribution Capacity
Gross Towing Weight (GTW):
5,000 lbs.
Tongue Weight (TW):
500 lbs.
Gross Towing Weight (GTW):
3,500 lbs.
Tongue Weight (TW):
350 lbs.
Weight Distribution Capacity
Gross Towing Weight (GTW):
5,000 lbs.
Tongue Weight (TW):
500 lbs.
Tech Tip
Vehicles using the 40455 wiring may need to see a local Ford dealer for a relay. The relay is needed to activate the tow package wiring circuit. No drilling required for installation , Access holes may need to be enlarged by drilling, filing, or rotary tool , Fits Hybrid models as well , Hitch does not fit vehicles with a factory installed hitch
Complete Towing Package for 2005 Ford Escape
Package Price:$379.25
2005 Ford Escape Owners Who Purchased This Trailer Hitch Also Bought...
Replacement Parts Available For This Product
Popular Escape Trailer Hitch Accessories
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Wrong item was ordered
- Did not arrive in time
- Product did not meet expectations
Customer Reviews
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" - 13650
Average Customer Rating: 4.8 out of 5 stars (520 Customer Reviews)
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.by: Ed05/08/2023
2009 FordEscape
Everything arrived fine and undamaged. The install video really helps. Having a second pair of hands to balance things will help. I just used a floor jack and a bottle jack to lift things up with the two bolts that point down and are to the front already in. After lifting just get those two nuts on and fish the rest in without a problem. Like others have said, why that extra spacer / washer on the front passenger side bolt, I put it on but see no reason for it.
I would like to know why it is there.
Ed
5/11/2023
Thank you very much for going the extra mile and getting a reply from Curt. My dad being a millwright could not see the why for it, but now I can tell him, it is there for a reason. Thanks again I will be ordering a new carrier soon if I cannot repair my old one. The original hitch got damaged when I got hit in the rear. No damage to my escape, a scratch or two. No broken glass, no airbag deploy or anything, but you can see the hitch got destroyed. The carrier bent pretty good, going to try and do some welding, I really only use it for deer hunting, So it does not need to be perfect or pretty. The Curt hitch appears to be a heaver tube and very good on the welds. Thank You!!!!!!
Ed
5/9/2024
It is a very good hitch and works perfect on my Escape. Customer support goes above and beyond, they replied to the question I had about the spacer in my original review without asking them about that spacer, and they are right, it is needed, so its in there on mine. Thanks for everything
Mike L.
5/23/2024
@Ed You're very welcome, we're glad we could help and thank you for the kind words!
by: Randal07/13/2019
After much research about hitches for my 2008 Ford Escape I settled on etrailer because of the detailed information concerning installation. I am visually oriented so having video to guide me was a huge help! In just an hour I had the hitch done! I need to use a small trailer from time to time and the car had no hitch on it. This will help me when I need to make a trip to the dump, haul off spring clean-up and get my Pelican boat to the lake. If their were ten more stars to click on I would click on number 10 for sure!
Randal
7/14/2020
Still looks brand new even after a North Idaho winter with all the road salt.
by: Marsolca08/10/2016
2007 Mercury Mariner
Installation was easy and the finish looks great. The only thing I would mention is that the instructions say a 2007 and later model year mariner/escape/tribute should have open ended frame rails and mine were sealed but a few minutes with some large drill bits took care of my access problem
Marsolca
12/12/2017
I got it to use with those extra cargo carriers. it was pretty easy to install into the car even by myself. Ive used the rack several times and when its not being used I bought a logo hitch cover that I really like for the extra advertising space instead of bumper stickers. Ive debated towing a trailer with it but I dont have one and I havent yet purchased the lighting wire harness.
by: Larry10/07/2013
2011 FordEscape
Thanks for the shipping upgrade and prompt delivery. The Curt hitch and wiring harness went on with ease just as advertised. I installed the hitch and wiring harness in my garage with the help of my 11 year old son (see attached photo). The video on etrailer.com was a terrific help. I am already looking for things to attach to my new hitch on etrailer.com. You have my business, and I will certainly pass along your web site to all in need of parts.
by: Jeremy05/02/2024
2010 FordEscape
Not much to say- it's a hitch, and it fit! Very fast shipping, and good communication. Will use etrailer again in the future.
by: Conner04/22/2024
Exactly as advertised, easy to install with instructions and tools, high qualoty.
by: Jeffrey M03/22/2017
2006 Mazda Tribute
Just completed the hitch install. It was very easy, had a little trouble around the exhaust but no big deal. Very nice hitch and shipping was fast. I will definitely recommend etrailer to anyone needing a hitch.
Jeffrey M.
3/27/2018
Had about a year now. Hitch is solid and no problems
by: James01/03/2024
2010 FordEscape
It's super sturdy holds up great under heavy loads extremely pleased with the product.
by: Brian S03/13/2017
2008 Mercury Mariner
This is the 2nd Curt hitch I have installed in the past two years, the other being on my 1996 F150. This one (13650) I installed on my 2008 Mercury Mariner, and I continue to be impressed with Curt products. Everything lined up perfectly and the hitch went on easily, looks great, and is way more heavy duty than anything I would ever need on a Mariner. No drill required on this one, leave it in the toolbox. I would recommend Curt hitches to anybody. My only complaint is, and this happened with both this hitch and the one I installed on my pickup, is they show up looking like they were dragged BEHIND the FedEx truck instead of inside of it. I was able to spot-paint the areas that were dinged/scratched down to bare metal, but it was very close to being returned/exchanged based on my opinion of what's acceptable. Other than this issue, it's a great product.
by: Curtis W.11/21/2012
2012 FordEscape
Install was fairly easy and straight forward. Like some other reviews, using the spacer on the passenger side did not allow the side holes to line up with the frame even when tightened, so I removed it and all bolts tightened just fine. The 2 in receiver will give me the added confidence for a loaded bike rack and utility trailer.
by: Dale09/23/2022
The product arrived this is the second time I have ordered from them and the shipping box was torn and had holes in it!!! The trailer hitch was starched but it a hitch not a big deal, but you would think they would use a heavyer grade of box.
Katrina B.
10/10/2022
Im sorry to see that your hitch has received some scratches on it due to shipping. This does tend to happen and when it does, we recommend using a Rust-oleum type paint to cover up any scratches and prevent corrosion in the future during use. I have a link below for your reference. I have also sent this information over to our Customer Service Department for them to get into contact with you.
Helpful Links
by: Tim Wilkerson 04/26/2015
2009 FordEscape
Great product easy to install the video on the web page was a lot of help. Very fast processing and shipping I will buy from etrailer.com again.
Tim W.
4/25/2016
Its working out great I never dreamed we would use it so much.
by: Kevin03/18/2013
2012 FordEscape
I installed this receiver on our 2012 Ford Escape XLT 4x4. Everything lined up perfectly. There was no interference from the the exhaust hangers. The fish wires worked great. The hardware slipped in easily from the end of the frame rails. I think it took a whole two beers from setup to cleanup to leisurely install this hitch.
by: Jerry08/08/2014
2012 FordEscape
Purchased for 2012 Escape XLT w/3.0 V-6. Installed it by myself today, which took a bit of planning. These are not a light weight product. Everything fit perfectly. My only suggestion for etrailer would be to cut the fish wires about 5 inches longer. They are just a tad too short to fish from the farthest bold position. I used a short piece of an old fish tape to extend mine, and everything went smoothly.
by: Dale Ross06/06/2016
2012 FordEscape
this product was as described and in excellent new condition when it arrived with in a week of ordering, no shipping charge. The hitch installed just as the instructions and the video outlined, using a floor jack I was able to install it by myself in less than an hour. looks great, solid and pretty.
by: Lenny05/12/2023
2011 Mercury Mariner
Product fit my 2011 Mercury Mariner just fine, install went fine by myself.
Packing was very beat up when it arrived, and powder coating was chipped off.
Better packing and I would have given 5 stars.
by: Doug06/20/2018
2010 FordEscape
Very nice fit. My only complaint was the thicker recommended spacer for above the exhaust caused the bolt to extend out at an angle and not far enough. I spent an extra hour trying to make this fit and then to remove it and install a standard spacer. This one hour job took me two hours. If I had another one to install it probably would only take me 30 - 45 minutes. I installed to use with a bike rack and possibly other cargo racks down the road.
by: Ryan Miller09/02/2014
Etrailer is doing things right with fast shipping and accurate information. This CURT hitch and T-one wiring harness was quick and easy to install.
by: T03/14/2017
2005FordEscape
Instructions say installs in 30 mins for professional and 60 mins for diy'er. Wrong. This is only true if you want to enlarge a existing hole large enough of pass through the bolt and brackets by grinding the metal unibody frame. I don't like grinding because latter it will rust. Even if you paint the spot latter it's better to find another way to pass through the harware. I removed the bumper and brackets to avoid grinding. This is why I'm a diy'er, because a shop probably would not repaint the exposed metal.
by: Jeffery07/21/2018
2010 Mercury Mariner
Very easy to do took less than 40 mins ( I did remove exhaust pipe from hanger for the install, just use some spray lube easy off, easy on) It was nice to have 2 bolt springs , one of mine got hung up & broke but having 2 in kit really helped.
I also removed the spare tire for the install was easy to do & made it easier to put on but not necessary.
I even used the box it came in to lay on the ground to do in my driveway, so easy to do without putting on a lift.
by: Nick04/25/2020
Good welding, good fit, good finish, easy installation. I will use it to tow a small trailer with my '05 Mazda Tribute. I opened the frame holes with an angle grinder and die grinder for extremely easy access (my frame is boxed). It took about an hour for prep, install, and cleanup (part of every job). All told- a very good value.
by: Ed E .05/16/2016
2012 FordEscape
I don't like to buy products on line but I did it when I needed a hitch for my excape. The hitch showed up in 3 days with regular shipping that was free. I do not have a garage or many tools I I hope it fit correctly and would be easy to install like the add said. It fit like a glove and was installed in a hr. I will tell anyone I know needing trailer products to give etrailer.com a try .
by: Matthew 08/11/2023
2007 FordEscape
Second trailer hitch I have bought from etrailer. They have the best "how to install" videos on YouTube.
by: Vincent 10/04/2023
Slightly more challenging than expected, but just needed to be patient when pushing the wire through to pull the bold. Holes lined up nicely and plenty of room to torque the bold.
by: Rick07/02/2017
2008 FordEscape
Could not believe how easy it was to install, did it by my self, and one jack stand, finished in a little over and hour. Everything sent with it, worked like a charm and wouldn't know it 5 of the 6 bolts went together great and the last one was a bit of a pain lol but it fit like a glove and looks great!!!!!!!!!
25
538
Show More Reviews
See what our Experts say about this CURT Trailer Hitch
- Will Curt Class III Trailer Hitch # 13650 Fit 2006 Ford EscapeYes, the Curt Class III Round Tube Receiver Hitch # 13650 that you referenced is confirmed to fit and will work great on your 2006 Ford Escape. This custom hitch will line right up to existing holes in the Escape's frame rails for a no-drill installation and all the necessary hardware is included. The hitch features a 3,500 pound towing weight capacity, a 350 pound tongue weight limit, and will provide you with a 2 inch receiver. I have attached an installation video and an article you...
view full answer... - Receiver Hitch Compatibilty and Towing Setup for a 2011 Toyota RAV4I was not able to find anything about the hitch you have fitting a 2011 Toyota RAV4. However, I do have a solution for you. I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver item # 75235. This is a custom fit, class III hitch, with a 2" receiver. It has a maximum gross trailer weight of 4,500 lbs and a maximum tongue weight of 675 lbs. I also recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118412. The T-One connector plugs directly...
view full answer... - Replacement Hardware Kit for Curt Trailer Hitch 13650We do sell replacement hardware kits for hitches like the Curt # 13650 that you referenced with the part number # RHK. On the product page you'd enter the part number of the hitch you have and then select the manufacturer. In this case it would be Curt.
view full answer... - Availability of Replacement Hardware for Curt Class III Hitch # 13650 on 2008 Ford EscapeWe can provide emplacement hardware to install a Curt # 13650 Class III hitch on your 2008 Escape. You would use part # RHK. On the product pate, type the hitch part number into the provided field, choose Curt from the drop-down menu and choose a quantity of 1. I've linked you to an install video showing the hitch being installed on a 2009 Escape. The procedure on your 2008 would be identical.
view full answer...
- Installation of Curt Hitch on 2012 Ford EscapeHe actually does install the spacer block on the passenger side for the # 13650 but I can see why it seems that way. At the 2 minute mark he says "I'll slide my block on first" but the camera is on the person helping with the installation on the driver side. The installer is on the other side and not shown in the video.
view full answer... - Two Inch Trailer Hitch Receiver for 2005 Ram 1500The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13650 is not a fit for your 1997 Dakota or 2005 Ram 1500. It is fit for 2005 - 2012 Ford Escape, 2005 - 2011 Mercury Mariner, and 2005 - 2011 Mazda Tribute. For your 2005 Ram 1500 you will want the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13333 which also does not fit a 1997 Dodge Dakota. It sounds like you have a hitch from a Dakota and it will not fit your Ram.
view full answer... - Replacement Hardware Kit for the Curt Trailer Hitch Receiver Part # 13650In order to obtain the bolts to attach the Curt Trailer Hitch Receiver part # 13650 to a 2005 - 2012 Ford Escape, 2005 - 2011 Mercury Mariner, or a 2005 - 2011 Mazda Tribute you would want to use the Replacement Hardware Kit for Trailer Hitches part # RHK. Once you have arrived at the product page for the replacement hardware kit, you will need to enter "13650" in the Hitch Item Number box and "Curt" in the Manufacturer drop down in order to receive the correct hardware. The replacement...
view full answer... - Hitch, Wiring, and Ball Mount Recommendations for a 2009 Ford EscapeFor your 2009 Ford Escape the Curt Hitch part # 13650 would be an excellent choice for a hitch. I attached an install video for you to check out as well. For trailer wiring you would want the Tow Ready Wiring Harness part # 118551. Install video attached as well. For ball mounts I recommend the etrailer Ball Mount Kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag.
view full answer... - Receiver Height of Curt Class III # 13650 When Installed on 2009 Ford EscapeAssuming that your Escape uses a stock wheel/tire, the top of the receiver for the Curt # 13650 would be 16 inches above the ground. Getting the trailer to tow so that it is level is not an exact science. If you can get it within 1-1/2 to 2 inches of level, you are doing just fine. It is better to have the coupler height a bit higher than level than lower. In addition to the hitch, wiring harness and ball mount, you might also need the following: Pin and clip, part # PC3 Locking stainless...
view full answer... - Comparing etrailer, Curt, and Draw-Tite Hitches for a 2006 Mercury MountaineerThe etrailer Trailer Hitch Receiver part # e56AR is the same as the Curt Trailer Hitch Receiver part # 13650, the only difference is finish. The etrailer hitch has a matte finish and the Curt hitch has a glossy finish. They all look pretty similar but I agree with you that the Curt hitch has a bit of a tighter fit to the rear bumper than the Draw-Tite. The same goes for the etrailer. I recommend the etrailer hitch if you are looking to save a few bucks and I personally prefer the matte...
view full answer... - The Best Trailer Hitch for 2012 Ford Escape to Use Folding Trailer Hitch Mount Cargo CarrierFor your 2012 Ford Escape I recommend Curt trailer hitch # 13650. When installed on a 2012 Ford Escape we found that it measured 1 inch from the center of hitch pin hole to the back of the bumper. I have linked a video showing installation and the measurement for you. The Flint Hill Goods 30" x 50" Wheelchair Carrier w/ 48" Ramp - 2" Hitch # FHG77ZR measures 4-3/4 inches from the center of the hitch pin hole to the nearest part of the carrier when folded up. This means that it will clear...
view full answer... - Recommended Trailer Hitch and Towing Accessories for 2008 Mercury Mariner w/ Backup SensorsThe presence of the back-up sensors will not have any bearing on the installation of a hitch. The Curt # 13650 would be an excellent choice that would work well for you. This hitch will fit whether or not your vehicle is equipped with the OEM 1-1/4 inch receiver. The fact that your Mariner has the back up sensors will mean that you'll need to use the # 118551 trailer wiring harness, if you'll be towing with your Mariner. It's been found that the # 118251 doesn't work on vehicles with the...
view full answer... - Trailer Hitch, Wiring, and Brake Controller Recommendation for 2011 Ford EscapeFor a trailer hitch for towing with your 2011 Ford Escape you would want the 2 inch Curt hitch part # 13650 which is a confirmed fit and has the same capacities as your Escape. The 2 inch hitch size means it will have more hitch accessories made for it and it will have higher capacities. Since you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4...
view full answer... - Difference Between Curt 13650 and 13651 on 2008 Ford EscapeThe difference between the two Curt hitches is the fitment. The # 13650 is designed for the 2008 Ford Escape that does not have a factory hitch installed. The # C13651 is designed to fit models with the 1-1/4" factory hitch.
view full answer... - Will a Hitch from a 2008 Ford Escape fit a 2012 Ford EscapeA hitch from a 2008 Ford Escape will fit a 2012 Ford Escape like the Curt Hitch part # 13650. What you would need to order is the part # RHK. On the product page you would need to enter the hitch part number and then select the hitch manufacturer. Based on the capacities you listed you either have the Curt Hitch part # 13650 or the part # C13651. You will need to check out the product pictures of either hitch so that you can compare them to the hitch you have so that you can pick out the...
view full answer... - Recommended Trailer Hitch Receiver For A 2008 Ford Escape HybridFor your 2008 Ford Escape Hybrid I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13650. Curt manufactures their hitches in the US unlike their competitor Draw-Tite so you can rest assured that your hitch has been rigorously tested and made for quality. Curt is also known for having a longer lasting gloss black powder coat finish over protective base coat that offers superior rust resistance when compared to their competitors. This hitch simply bolts onto the...
view full answer... - Will Using a Trunk Mount Bike Rack Scratch or Damage Paint on a 2008 Ford EscapeAnything that makes contact with the vehicle has the potential to mar or scratch the paint. You would need to make sure that the vehicle and rack are clean where they come into contact with each other. Also, a coat of wax in those areas on the vehicle will also help add some protection. The straps are long enough to secure the rack to the vehicle. You will not need extra straps. The Thule Passage # TH910XT does not come with any locks. Based on your concerns a hitch mounted bike rack...
view full answer... - Trailer hitch and Bike Carrier Recommendations for a 2011 Ford EscapeSince you only need to carry 1 bike what you could do is instead of installing a trailer hitch use a trunk mount bike carrier. This way you would only need the carrier instead of a hitch and carrier. The Thule Passage 2 # TH910XT is a popular and inexpensive carrier that is listed as a fit for your 2011 Ford Escape. I have included a link to a video review for you. If you would rather go with a hitch then take a look at the picture I have included that shows what the dampener looks like....
view full answer...
- Hitch, Wiring, Ball Mount and Hitch Ball for 2012 Ford Escape Without Factory Tow PackageCurt 2-inch Class III hitch # 13650 is a USA-made hitch that fits the hybrid and standard versions of the 2012 Ford Escape. This hitch offers no-drill installation on the Escape without a factory hitch. An install video is linked for you along with the written instructions from Curt. For a 4-pole wiring harness for the Escape without the factory tow package use part # 118251 if you do NOT have the backup sensors. Models WITH backup sensors can use # 118551. For a ball mount for towing...
view full answer... - Trailer Hitch and Wiring Kit Fit Confirmation for 2012 Ford EscapeThe Curt hitch part # 13650 is a confirmed fit for your 2012 Ford Escape. The # 118551 that you referenced is also the correct fitting wiring kit as well. To adapt the 4-way to a 7-way and if you don't have trailer brakes you would only need the part # C57674 that you referenced as well. If you do have trailer brakes you would need the # ETBC7 instead of the # C57674 and a brake controller. This kit comes with everything needed to wire up the 7-way and install a brake controller. For...
view full answer... - Availabiliity of Hitch-Mount Bike Rack For Use While Towing Small Trailer With Class II HitchYour 2008 Mercury Mariner can be equipped with either a 1-1/4-inch Class II or a 2-inch Class III trailer hitch. There are many towing-type bike racks available for use with 2-inch hitches however there are no towing racks offered for use with Class II hitches that have a 1-1/4-inch receiver. This is because the lighter-duty Class II hitches do not have the capacity required to handle the forces applied to the ball mount from an attached bike carrier. Your options are then to either replace...
view full answer... - Comparing CURT Class III Trailer Hitches for a 2008 Ford EscapeThe CURT Trailer Hitch # 13650 and # C13651 are very similar. The 13650 has some additional hardware and updated instructions that make it compatible with the 2012 Ford Escape. The 13651 hitch only includes up to 2011 on the Ford Escape. The other difference is that the C13651 will fit if the vehicle has a factory 1-1/4 hitch already installed. I have incldued a link to the installation details for the 13650 as well as a video showing a typical installation. If you plan on doing some towing...
view full answer... - Something is Rattling After Installing Curt Class III trailer Hitch on a 2005 to 2012 Ford EscapeYou could be hearing the ball mount rattling around in the hitch or it could be the exhaust making contact with the hitch. To stop movement of the ball mount you can use an anti-rattle device such as # MPG908. If the problem is the exhaust then there are some things you can do to correct the issue. I have included a link to a how-to article that will help you.
view full answer... - Exhaust Hanger Touching Hitch and Transferring Vibration and Noise through a 2010 Mercury MarinerI am looking at the install pictures and if I am reading things correctly, the steel hanger welded to the exhaust pipe is touching the hitch. This in turn sends exhaust vibrations into the vehicle and that is what you are hearing. You have a few options of how this can be corrected. The first is what we do here in our shops, and that is simply re-bending the hanger so that things do not make contact. The hangers are not always welded on the same way at the factory and some times they warp...
view full answer...
Do you have a question about this Trailer Hitch?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Randy B
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Andrew L
Video Edited:
Dustin K
Video by:
Andrew K
Video by:
Kathleen M
Video by:
Chris R
Video by:
Zach D
Written by:
Lindsey S
Updated by:
Wilson B
Updated by:
Amanda M
Updated by:
Kristina F
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
5/9/2023
I reached out to Curt about the use of the spacer and washer on the front passenger side bolt. The main answer is that it is there to keep the receiver at the designed angle and to fill the gap on the frame of the vehicle. I hope that this answers your question.